Models > A3520SPN > Instructions

A3520SPN Admiral Range - Instructions

All Instructions for the A3520SPN
106 - 120 of 129
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
burner would go to high when turned on
Pulled stove out to unplug. Removed screws holding end covers then remove screws on the underside of cover as you face the stove top.Remove knobs.Pull bottom cover forward and up so you can lift it off to see the insides.Remove wires and attach to the new part one at a time. Unscrew old from the front and attach the new one.Put it back together.Done.
Parts Used:
Range Infinite Burner Switch - 8 Inch
  • James from Fairmont, WV
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
heating coils would not work
Remove heat coils, take body of coil inserts out, remove screws from body, cut old receptacle out, tie new recptacle wires to the old piece of left over wires using wire nuts, and reassemble body, insert heating coils and test.
Parts Used:
Surface Burner Receptacle Kit
  • Adam from Kempner, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Elements did not fit properly.
Ordered the parts, installed.
Parts Used:
Chrome Drip Bowl - 8 inch Drip Bowl - 6 Inch Economy Y-frame Surface Unit - 6" Economy Y-frame Surface Unit - 8"
  • myrna from homestead, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
replace the cook stove's drip bowls instead of cleaning them
I removed the burners and then the older drip bowls of the cook stove--and then I put on the new drip bowls and put back on the burners. My mechanical skills were sufficient for the replacement of the drip bowls.
Parts Used:
Chrome Drip Bowl - 8 inch Drip Bowl - 6 Inch
  • Dallas from Arlington, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
burned out switch
killed power...removed back of stove...removed switch and replaced it..reinstalled back...powered up
Parts Used:
Range Infinite Burner Switch - 8 Inch
  • KENNETH from DEEP RUN, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
surface burner stopped working. Was not heating up.
The repair only took me 10 minutes to do. I purchased the surface replacement kit from partselect.com. The part arrived in two days. The instructions were very simple. I read the instructions on line during my purchase. When I received the new part, I simply did the repair. Including shipping, the cost was less than $20.00. A service call would have been at least 5x the cost. Thank you for being there Partselect. (Tim from south bend indiana)
Parts Used:
Surface Burner Receptacle Kit
  • timothy from south bend, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Vent Cover Corroded from Years of Use
1. Ensure oven is powered down and cool to the touch. For extra assurance, throw the circuit breaker to the range to OFF. 2. Pulling gently but with constant force remove the right rear surface burner element from its receptacle. 3. Remove right rear drip bowl. 4. Using a #2 Phillips screwdriver remove the single screw that holds the vent cover. 5. Lift the oven top, it should latch open. 6. Remove the vent cover - you may need to pry it very slightly with a slot screwdriver if it has never been removed, it tends to stick from accumulated cooking smudge. 7. Clean up the area where the new cover will go. 8. Install the new cover and screw it snugly, but don't overtighten. 9. Using releases on latching struts,lower oven top. (Cautiously, so as not to pinch your fingers as the top drops!) 10. Re-seat the drip bowl and carefully plug the heating element back in, making sure it seats properly in both the electric receptacle socket and how it sits on the stove top drip pan. Done! (Don't forget to switch the breaker back on, if you turned it off.) I explained this in great detail, but it shouldn't take more than 5 or 10 minutes to accomplish the whole task.
Parts Used:
Vent Cover - Silver
  • Scott from Jacksonville, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
I needed to replace to two 8* drip bowls on the kitchen range
(a) I took out (and threw away) two stained 8* chrome drip bowls on my kitchen range; (b) ti put in two new 8" chrome drip bowls on my kitchen range. I'm pleased that I was equal to the task.
Parts Used:
Chrome Drip Bowl - 8 inch
  • Dallas from Arlington, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Stove needed new bowls
Just dropped in
Parts Used:
Chrome Drip Bowl - 8 inch Drip Bowl - 6 Inch
  • Karen from Kettering, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Old dirty drip pans
Removed heating element, installed new drip pan, replaced heating element. Was amazed at fast delivery - ordered in afternoon, arrived fed ex next morning!
Parts Used:
Chrome Drip Bowl - 8 inch
  • gizella from mays landing, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Burner did not heat
New receptacle element. I am a girl and I did it.!!!!
Parts Used:
Surface Burner Receptacle Kit
  • lula from Antelope, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Not heating
Was easy cut the wires of as told to do wire nut the ends together and put back together and tested and worked great. Done
Parts Used:
Surface Burner Receptacle Kit
  • Darwin from wisconsin rapids, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Two old Surface Burner Receptacles needed to be replaced.
I followed the instructions given on your great site. Thank you so much.
Parts Used:
Drip Bowl - 6 Inch Chrome Drip Bowl - 8 inch Surface Burner Receptacle Kit
  • Willis from Anaheim, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Replace 8" Element Switch
Disassembled upper unit with Phillips screwdriver. Removed 2 "plug connectors" from element switch. Replaced switch. Plugged both connectors back onto switch. Reassembled the upper portion of the range. Tested and OK
Parts Used:
Range Infinite Burner Switch - 8 Inch
  • John from Summerfield, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Drip bowls tarnished.
Remove heating element coils. & old drip pans. Install the new drip pans and reinsert the heating elements and insure all elements were level. For aesthetic reasons I replaced all the drip pans - 2 x 8" & 2 x 6".
Parts Used:
Chrome Drip Bowl - 8 inch
  • Jennifer from Albion, NE
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the A3520SPN
106 - 120 of 129
Back to Top