A31713XAAL Admiral Range - Instructions

Replaced stripped screws with 632 by 3/8 bolts and nuts. Your video helped with the rest of the installation.

removed rear cover where the spark module was and change it

Unplug power cord to oven.Remove lower panel from inside of oven to access flame rail cover.Remove wingnut from cover to access flamerail and igniter.Using phillips head screwdriver,remove 2 screws from lower access plate located at rear of oven to access igniter wiring.Disconnect both wires, then using a nutdriver,unscrew and remove igniter from flamerail.To install, simply reverse instructions.It was extremely simple and fun to do.But most rewarding of all was the sense of accomplishment from doing the repair myself not to mention of course the money i saved not having to call a technician. Thanks guys!

Used strap wrench to turn out. Rust build up under the burner. Used flat screwdriver to loosen under burner and strap wrench to turn out. Then replaceing the igniter was very easy.

I have worked in maintenance field most of my adult life and all aspects and to change the oven door gasket was no challenge what so ever. It took longer to find my needle nose pliers to remove the old gasket clips and then re-install the new gasket. Maybe 10 minutes total

Because of the video provided by Parts Select I felt confident before even starting and that confidence stayed with me to the end..I removed bottom of oven , removed the philips screw in the front end of the burner and removed it.. Losened and removed the igniter replaced it and reassembled..The only caution I can give, if you find the screws holding the ignited on the burner hard to take off, apply a SMALL amount of WD40 to the threads and wait a couple minutes before removing..I was fortunat in the fact that my plug matched the replacement part with no cutting of wires..I normally don't get breaks like that.. Thanks Parts Select.

First turn gas off at pipe. Remove oven door, racks and bottom cover. Go to back of oven and unplug oven igniter. Back in front, unscrew 2 nut screws from igniter. To make things easier I tied a piece of string to the plug of the igniter, once I unscrewed the igniter I pulled it out with the string attached. When replacing I tied the string to the plug of the new igniter and pulled it from the back so the plug was able to come through, plug in the new igniter, screw it in place, replace the racks, covers, door and you're ready to enjoy some baking

Based off the information I found online, I determined we had a bad igniter. 1- disconnect oven from any power sources. If you have a gas model, be sure to valve off gas at this time as well. 2- Remove the racks and bottom pan in the oven. There is 2 push/pull locking mechanisms at the back of the oven that hold the tray in. Once you have this out you should have access to the gas tube and igniter. 3- Using a 5/16 nut driver, remove the 2 bolts on the mounting plate and the igniter should be free at this time. 4- Remove the bottom drawer to the oven. This will give you access to the electrical connections. 5- Remove the 2-3 screws that hold on the access panel toward the back of the unit. 6- Following the wires down, find the plug for the igniter and unplug. After this is done pull the wiring up through the oven and it will be the same to put back together just in reverse order. Relatively simple project that should take anywhere from 10-30 minutes depending on how handy you are. After reinstallation our preheat times went from 45 minutes to 10

Hardest part was disconnecting the gas line and moving the range out of the counter. Removed oven door for easier access to the igniter from the front. And the clean up. Installing the igniter was relatively easy from the rear of the range. I was not able to install the igniter through the front of the range because the wires were not long enough to pull the igniter forward through the front so it was necessary to pull the range out from the counter and install it from the rear. Then it was just a matter of removing a small dust cover at the rear by removing one screw. Then removing old insulation and disconnecting wires. Remove 2 mounting screws that held the igniter in place. These screws had to be removed from the front. Pushed the old igniter out through the rear of the range. Connected the new igniter wires. Pushed the new igniter through the rear of range and replace the new insulation. Mounted the new igniter with 2 screws. Reassembled everything and it worked ok.

removed cover over burner section ,removed power to burner section ,removed burner assembly, replaced ignitor assembly, wire in to control circuit ,replace burner section in oven,turnon power chech operation ,replace cover.

UNPLUG THE POWER CORD! This particular model is a (slide-in) unit, it was wedged between to fixed cupboards/cabinets. Therefore, there are really no side panels to speak of, this made the repair slightly easier. I simply slid the unit out enough to unplug the power cord and access the right side of the unit. All one needs, at this point, is a Phillips head screw driver to remove a small metal panel installed just below the stove top panel (right side of range), its held with approx. 8 screws. There is one other panel that must be removed as well, (you may want to remove this panel first). It is an enameled-like panel approx. 5" wide x 36" long located at the front of the range (right side) running the length/height of the range (held with 2 screws). Get those 2 panels removed and you will see the spark module attached near center of range just under stove-top panel. Module is attached to a small metal bracket, module has 6 wires attached to it (2 feeding the module and 4 exiting the module to the burners). Bracket screws are nearly impossible to get at (you need a very stubby Phillips screw driver, if you can even get your hand in there). Anyway, I simply released the module from the bracket, then carefully bent the bracket back toward me; to provide work area for my hands. The bracket bends easily and really can't be broken. Now, at this point (using longer needle-nose pliers) detach the wires from the old module (remembering each wires location) or, as I did, hold the replacement module near the existing module and transfer the wires one at a time. Now, slap it all back together as you took it apart. Really simple job, total time is easily/generally under 30 minutes. It may be easier to access the module by removing all the burner components and raising the stove-top? Not sure? I chose not to do the repair that way. Hard part was locating where the manufacturer hid the module on the range. :- ) D.I.Y.ers Rock!!!

I think the installation instructions are fairly self explanatory. This is the second item I've ordered from Parts Select and I'm thrilled with their service. The items are always less expensive than other sites and they deliver what they promise. I would highly recommend them.

Popped in there real quick. Wish I would have done it sooner, my oven heats up much faster.

Removed door, took off old igniter. Had to redo plug , simple, because kit had wires to splice to make it work. Whole job was 30 min. Recomend to anyone. Saved $75 on a service call. Bill

removed inside trays and grill inside large oven door on front to get to ignitor,removed ignitor with 1/4 drive socket,followed the wires off the ignitor thru the hole in back of oven and disconnected the connector,put on in reverse order.To simple to even write about,anyone can look at it and tell what needs to be done