A31713XAAL Admiral Range - Instructions

I simply followed the "general" instructions from the online video "Partselect" provides and perused the instructions included in the kit. The OEM igniter was much longer than the replacement but the new part was spec'd just fine. It was necessary for me to open up the back of the stove in order to retrofit the igniter leads to the original block connector and install the heat resistant padding included in the kit. The additional necessary hardware fit very nicely inside the oven. The stove's oven fired up without any problems and spared me the expense of purchasing a new oven. Thank you very much "Partselect".

I removed and replaced the igniter. I described these symptoms on the web site and it detailed that90% of the time by installing a new igniter it will fix the described problem. So I ordered the part and installed the part and everything worked OK. The only tool I had to use was a screw driver to remove three screws. It took about half an hour. If I had to do it again it would take about 15 minutes.

Unplugged oven. Removed door,racks,and bottom shelf. Removed screws from ignitor and unplugged it from connection. Installed new ignitor with screws and plugged in to connection. Tucked wires behind insulation as they were before. Installed previously mentioned items and turned on to check. Worked great and am very pleased with PartSelect and the assistance they offer.

Ordered oven Igniter kit PS1573892 which cost $73.00. Received the kit with instructions easy to follow to install. I was surprised how easy it was to repair, with the help of my wife we did the job in about 2 hours, the oven now works great. I really saved a bundle of money doing this myself, a local repair service wanted $114.00 for the same part and $200.00 labor to install and this is the gospel truth. I am 96 years old. RMA Bluefield, WV

Removed burner pan screws,igniters, gas tubes & burners. Changed 2 igniters, removed rust & repainted ends of 2 of the tubes (heatproof paint). New burners were made a hair smaller than original but locked in O.K...Now, the hard part...disconnected all four tubes from gas valve assembly. (Had to shut off gas to house in order to remove main gas line to stovetop.) Had to remove valve box in order to remove/replace frozen valve. Unit is 25 years old, works as and looks new...Rust was caused by boil-overs.

Take off oven door, remove racks, lift out bottom plate of oven, remove deflector shield, unbolt old igniter gently fish out the wire and plug from the back of the oven. Unplug and replace with the new igniter. re-assemble oven.

Followed the directions on the video. Very easy to do.

The burner head caps on my Magic Chef no longer work and had to be replaced. I ordered 1 of the 4 caps to see how it would work out for me. I did not have any issues replace the cap. I contacted PartSelect and order the other 3 caps. The sales representative took my order and was EXTREMELY helpful. Now I know why all of my neighbors choose PartSelect. Including the cleaning, it did not take me more than 15 minutes. The video was also extremely helpful. Our Magic Chef should be good for another 6-8 years. Thanks PartSelect.

turn burner cap counter clock wise lift out remove to leads,do not have to turn power off they are mini volts.Insert the two (leads)weirs on to new cap,twist back in done.Fire it up.

The spark module pulses a stepped up voltage to all four burner sparks at the same time regardless of which burner you want to ignite. I read that this part lasts about 10 years. I don't cook much and it lasted 13 years. On my Magic Chef the part is behind the right side wall panel. Lift the range top,remove all the screws that hold the right side panel in place. This replacement can done without opening any gas fittings.

The oven in my Jenn-Air range started to leak gas whenever I turned it on and a visit from the local gas company indicated the ignitor had probably gone bad. I had assumed the older range wasn't worth repairing but didn't want to spend $800+ for something in otherwise excellent condition. Internet research yielded lots of tutorials on how to make the swap and I decided to see if I could get the old part out before going any further. It wasn't too tricky except one of the two screws holding the ignitor in place had stripped and it was in a location that was very difficult to reach. I used a part of tin snips to cut around it. The new part ordered here came very quickly and exactly matched what I had removed; the wiring harness fit perfectly. It was a snap to put back in and now the oven works perfectly. All for under $50.

My oven would not come on so my wife could bake a cake. The glow coil that ignites the gas for the oven had burned out. The replacement went very easily and fast. This web site was very helpful with all the information I needed to get it up and running again. I enjoyed the cake she made after I got it fixed.

We replaced 3 of 4 igniters on the stove top according to the previously submitted recommendations. Easy to do butt after putting one of the modules back together, we found one igniter still didn't function. We discovered the solution was to run the connecting wire under the gas tubing. Apparently it was compressed when it was over the top of the tube and not under it.

Removed oven door, bottom, bottom of broiler and back metal shield. Just unscrew old igniter and unplug wires and install in one. No problems.

My used stove had been dropped by the previous owner. While I could live with the minor scratches on one side the wooden shims holding up one corner were annoying. A new leveling leg was less than $2. I used a pair of needle nose pliers to straighten the mounting hole and screwed the new leg in. This used stove was originally $2000 but I bought it for $999. the new leg plus shipping was about $10. What a deal.