A3110PPA Admiral Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven rack lost in a garage fire
First I opened the door to the oven. Then I opened the box that the part came in. (knife) I then slid the oven rack out of the box and unwrapped the plastic, being careful not to bend or scratch the new rack. Now, this is the tricky part... I had to move the existing rack down one space to make room for the new one. Then carefully slid the new rack in, tipping it slightly and sliding it in. LOL
Parts Used:
-
Bob from Saint Clair Shores, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
29 of 37 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
leak
removed then installed new unit by hand. received order the next day-am. delivery time great.
Parts Used:
-
George from Plainville, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
12 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven floor panel was warped.
It was so easy, I pushed the panel towards the back and lifted the front up then lifted it right out. I am so glad that you had the part. I ordered it and when it got here, I just sliped it right in, perfect fit! Thank you so much! Cindy Brison
Parts Used:
-
Cindy from Colton, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
8 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
30 year old gas stove needed a new burner assembly.
We lifted up the stove top, slipped the burner assembly in. It fit! who knew that we could get a part to an old stove without the model number, just by looking at a picture of the part! Terrific!
Parts Used:
-
Caroline from South Windsor, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
6 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gas manifold had holes in it.
Removed locking wire from bottom burner assembly then I pulled the element out and replaced with the new one.
Parts Used:
-
Mr. J.C. from Haines City, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
5 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Racks were dark and dirty
The first set of racks did not fit. I called the Service rep, gave him the model number and exchanged the racks for the new ones. The new ones fit perfectly and the service was excellent. I would definitely recommend PartSelect.com to anyone who wants to deal with a company with excellent service, parts and representatives who know their stuff.
Parts Used:
-
Geraldine from Germantown, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
6 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Freont Burners Of Both Units Had Rusted Though Over The Years Of Boilover.
Lifted lid, removed old burner units, replace with new ones. In less than two min. Was back up and cooking.
Parts Used:
-
Angelo W. from Chirfland, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pilot light would go out when oven was turned off but still allowed gas.
l removed the top section after the grates. Then l took the phillips screws out of the three brackets which hold the L brace which supports the controls,thermostat and the regulator. Only because l did not have a closed-end ratchet wrench for 1/4" and l could not locate my 1/4" socket for my small rachet. l disconnected all gas lines and the thermocouple, then l used the power screwdriver without the apex which makes it a great power 1/4" nutdriver and took out the two screws holding the thermostat. Then l just reversed all the steps installing the new thermostat and once l got the air out and gas was pure l lit the pilot lights and everything worked great. And l adjusted my top burner pilot lights a little higher to prevent them from gettig blown out so easy. Done deal.
Parts Used:
-
Steven from Oklahoma City, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
5 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
floor panel heavily stained and warped
-
Joel from Monroe, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
3 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I needed a broiler pan
I took the broiler pan out of the shipping container and put it in the oven.
Parts Used:
-
Rhoda P. from Secaucus, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
4 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The oven bottom was warped and could not be positioned properly in the oven.
Removing the old oven bottom was easy...as it was already outside of its slots. Installing the new one was pretty easy. I placed the oven bottom in the front slots first...then the rear slots...no tools necessary.
Parts Used:
-
Tara from ALBANY, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven Racks were old
-
Sandra M from DISTRICT HTS, MD
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original rack had melted plastic on it.
-
Linda from BURBANK, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Thermostat bulb was hanging loose
Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub
Parts Used:
-
Willi from Old Saybrook, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
2 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The floor panel of the oven was pocked and in bad shape
I found the panel on the innernet, ordered it and when it arrived I removed the old one and replaced it with the new one.
Parts Used:
-
Roger from San Juan Capistrano, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!