A3100PPW Admiral Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The burners were old and loose
First, I raised the top. Extracted the holding pin, Then replaced the burner. Then reinserted the holding pin. Two minutes top's.
Parts Used:
-
James R. from Corona, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
unable to see the numbers on the old knob.
-
Patricia from SAN LEANDRO, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
1960's oven door gasket fell apart, actual gasket not available any more
Chose rubber flexible gasket with metal tabs. cut to size. unscrewed metal bracket on inside oven edge on 3 sides, slipped metal tabs between oven and metal and screwed back in. Done! Not a perfect fit but pretty good - better than no gasket.
Parts Used:
-
Mary from WINCHESTER, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My oven door seal had dried rotted
I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.
Parts Used:
-
Anita from ELKTON, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven knob was broke
-
Sara from FORT RIPLEY, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old seal breaking off oven door. Oven not baking food well, wasting heat and fuel.
Used pliers to remove clips and old seal. Snap in new seal. DONE! Less than 5 mins.
Parts Used:
-
Mz from COLUMBIA, ME
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original rack had melted plastic on it.
-
Linda from BURBANK, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The oven bottom was warped and could not be positioned properly in the oven.
Removing the old oven bottom was easy...as it was already outside of its slots. Installing the new one was pretty easy. I placed the oven bottom in the front slots first...then the rear slots...no tools necessary.
Parts Used:
-
Tara from ALBANY, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
my knobs were broken on 30 year old range
I took a pair of channel locks pulled the old one off pushed the new one on they look really nice and was glad they had the parts for such an old stove. thank you,now my hubby is glad so he doesn't have to buy a new stove.
Parts Used:
-
Larry from LAWTON, MI
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven Racks were old
-
Sandra M from DISTRICT HTS, MD
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The oven control know wore out.
I purchased a knob that I was hoping might fit properly.
Unfortunately I did not find anything that matched the knob we had originally. We use the knob that I purchased to turn the oven on and off, but the shaft channel is much longer than the shaft on the stove, so the knob sits high above the other knobs. I wish that I could find a knob to accommodate the
shaft on the stove. I have considered purchasing an addition kinob and trying to saw off part of the shaft if the plastic can be shortened without shattering.
Unfortunately I did not find anything that matched the knob we had originally. We use the knob that I purchased to turn the oven on and off, but the shaft channel is much longer than the shaft on the stove, so the knob sits high above the other knobs. I wish that I could find a knob to accommodate the
shaft on the stove. I have considered purchasing an addition kinob and trying to saw off part of the shaft if the plastic can be shortened without shattering.
Parts Used:
-
Judy from ARDSLEY, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Thermostat Knob
After ordering 3 or 4 different knobs for replacement, I found the one I needed. I did not have the oven model number at first...now everything is working fine. No tools, just push the knob into place. Thanks!
Parts Used:
-
Kathy from Fremont, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Thermostat bulb was hanging loose
Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub
Parts Used:
-
Willi from Old Saybrook, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
2 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed to replace two stove valve knobs.
-
Roberta from BROOKLYN, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip pans were rusted. I had shopped for replacements at local appliance stores without finding them.
Removed the rusted drip pans and replaced them with the new pans. Range looks great and ready for many more years of use!
Parts Used:
-
Norma J from Philadelphia, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!