A3100PPA Admiral Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
worn out door seal
removed old clips and remaining parts of old seal...new part already had clips attached, so just snapped them into holes in oven door.
Parts Used:
-
Stella from Charlotte, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
31 of 32 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven rack lost in a garage fire
First I opened the door to the oven. Then I opened the box that the part came in. (knife) I then slid the oven rack out of the box and unwrapped the plastic, being careful not to bend or scratch the new rack. Now, this is the tricky part... I had to move the existing rack down one space to make room for the new one. Then carefully slid the new rack in, tipping it slightly and sliding it in. LOL
Parts Used:
-
Bob from Saint Clair Shores, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
29 of 37 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
leak
removed then installed new unit by hand. received order the next day-am. delivery time great.
Parts Used:
-
George from Plainville, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
12 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door Seal on oven was old, hard and breaking apart.
It was very simple, pull off the old one, then I took some pliers and pulled out the fasteners. Took new gasket from bag and it just snapped into place.
Parts Used:
-
Kenneth from Friend, NE
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
10 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven floor panel was warped.
It was so easy, I pushed the panel towards the back and lifted the front up then lifted it right out. I am so glad that you had the part. I ordered it and when it got here, I just sliped it right in, perfect fit! Thank you so much! Cindy Brison
Parts Used:
-
Cindy from Colton, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
8 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Seal was fallinig off
My husband did it. I was not there to see it. He said it took less than one minute, just snapped in and worked beautifully.
Parts Used:
-
Marilyn from Fresno, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
7 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Over wouldn't light.
Saw that the igniter came on, but no gas flow.
Unpluge stove. Remover bottom of oven to have access to flow valve. Remored sheet metal cover.
Removed burner. Unpluged flow valve and removed it.
Unpluge stove. Remover bottom of oven to have access to flow valve. Remored sheet metal cover.
Removed burner. Unpluged flow valve and removed it.
Parts Used:
-
Bob from South Beloit, IL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Wrench (Adjustable)
8 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
30 year old gas stove needed a new burner assembly.
We lifted up the stove top, slipped the burner assembly in. It fit! who knew that we could get a part to an old stove without the model number, just by looking at a picture of the part! Terrific!
Parts Used:
-
Caroline from South Windsor, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
6 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Stove seal fell apart
Removed old seal parts and had to cut new part to put into space but it went in without difficulty and has sealed the stove door tight again.
Parts Used:
-
Teresa from Washougal, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
5 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gas manifold had holes in it.
Removed locking wire from bottom burner assembly then I pulled the element out and replaced with the new one.
Parts Used:
-
Mr. J.C. from Haines City, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
5 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad Door Gasket.
First I took the new gasket out of the plastic bag to make sure it was the right size. Then I proceded to take the old gasket out by pulling it with a long noise pliers. Then I took the new gasket and went around the door putting the pins in the holes that, the old gasket was in. That,s about it.
Parts Used:
-
Donald from Schuylkill Haven, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
5 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven door gasket torn
ordered wrong part, called, was sent return number, sent part back, account credited ... easy return policy ... friendly people, good job
Parts Used:
-
Ovide N from Abbeville, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Racks were dark and dirty
The first set of racks did not fit. I called the Service rep, gave him the model number and exchanged the racks for the new ones. The new ones fit perfectly and the service was excellent. I would definitely recommend PartSelect.com to anyone who wants to deal with a company with excellent service, parts and representatives who know their stuff.
Parts Used:
-
Geraldine from Germantown, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
6 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Freont Burners Of Both Units Had Rusted Though Over The Years Of Boilover.
Lifted lid, removed old burner units, replace with new ones. In less than two min. Was back up and cooking.
Parts Used:
-
Angelo W. from Chirfland, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
floor panel heavily stained and warped
-
Joel from Monroe, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
3 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!