Models > 91194400300 > Instructions

91194400300 Kenmore Range - Instructions

All Instructions for the 91194400300
346 - 360 of 383
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Lower element wasn't getting hot.
Removed four screws from rear panel and two screws from element. Then removed the two wires from the element. Replaced element and the two wires along with thesix screws. It a grand total of five minuets on thanksgiving morning. Just in time to finish the rest of the meal.
Parts Used:
Bake Element - Push On Terminals - 240V
  • Sherman from Seguin, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
lower oven heating element out
Hardest part was dragging oven away from wall and cleaning floor. Unscrewed 2 oven screws holding heating element in. Unscrewed 4 back screws holding cover panel on back. Unclipped connections. Heating element slid right out. Put new one in, reclip wires and put screws back. Simple. Usually I'm 10 thumbs so this simple repair was mentally uplifting.
Parts Used:
Bake Element - Push On Terminals - 240V
  • Mark from Memphis, TN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Bottom element burned out
Repair was very easy. Removed two nuts with nut driver and unhooked old element and new element slipped right on terminals. Replace nuts with driver and we were ready to go.
Parts Used:
Bake Element - Push On Terminals - 240V
  • Richard from Buchanan, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
oven would not heat up
took off old heating element and replaced with new heating element. no appliance store in my area had the replacement element. googled heating element and found the site and ordered part. had part within 5 days.
Parts Used:
Bake Element - Push On Terminals - 240V
  • Alan from Shamokin, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Oven light wire broken, damaged socket
Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.
Parts Used:
RECEPTACLE PUSH-IN
  • Patricia from Brandenburg, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
Replaced my drip pans
The new drip pans are great. I had purchased generic ones locally that were supposed to be universal. The problem was that they did not fit right and the burner coils did not sit flat. The new drip pans fit well and look great too.
Parts Used:
Drip Bowl - 8 Inch Drip Bowl - 6 Inch
  • Nancy from Mead, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Broil element broken
Never did a repair like that. Had to ask store clerk what you call that thing you take off bolts with. But repair went great. Very satisfied. Part arrived very quickly and saved our Christmas dinner. THANK YOU!
Parts Used:
Broil Element
  • Laura from Stratford, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
bake element broken in two parts
its easy take the plate off pull it out disconnect the leads i used locking pliers to hold the leads from going up into the insulation until i installed the element 10 min easy .
Parts Used:
Bake Element - Push On Terminals - 240V
  • patrick from pawnee, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Socket set
Was this instruction helpful to you?
Thank you for voting!
I ord. drip pans for my Mother in another state
The drip pans arrived and she switched them out with the old ones Easy!
Parts Used:
Drip Bowl - 8 Inch Drip Bowl - 6 Inch
  • Susan from Alpena, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
My drip bowls were rusted and corroded
I ordered new drip bowls and put them in place. They fit just fine.
Parts Used:
Drip Bowl - 8 Inch Drip Bowl - 6 Inch
  • Glenda L from Lake Placid, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Right front burner not getting hot
After searching the internet for a cause for the burner not getting hot it looked as though it was the burner switch. I ordered the switch and installed it. Behold it still did not work. I then ordered the burner, installed it and it worked. So I had a 50/50 chance as to which part was the problem. This was my first stove repair and I found it easy to do. Finding something to hold up the ceramic cooktop took the most time. I cut a piece of wood to prop it up while I replaced the burner.
Parts Used:
Surface Burner Switch - 8 Inch - 2100W
  • Cory from Honesdale, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
needed new drip pans-
replaced pans- what I would like to comment on is the time- I ordered one day at noon and had them the next day at noon- I live in tiny town on northern border of USA- it was awesome- I couldn't believe it was them- 24 hours- super job and excellent price too
Parts Used:
Drip Bowl - 8 Inch Drip Bowl - 6 Inch
  • Connice from Massena, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Open Switch
Pull knob. Pull wires. Pull two screws. Replace switch
Parts Used:
Surface Burner Switch - 8 Inch - 2100W
  • John from Denham Springs, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Drip Bowels badly stained.
Unplug heating elements and pick up drip bowels and reinstall elements.
Parts Used:
Drip Bowl - 8 Inch Drip Bowl - 6 Inch
  • Dean from Hill, NH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Mine was easy
I ordered new oven racks. My old ones were the original with the range (uncleanable). I cleaned by oven till it shined and when I put in the new racks it looked like a new oven. I'm very happy.
Parts Used:
Oven Rack
  • Barbara from Bowling Green, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 91194400300
346 - 360 of 383
Back to Top