91193490300 Kenmore Range - Instructions

Yeah, so I didn't read the manual the first time we ran the self-clean cycle on the oven. Something about taking the racks out. So these were my little reminder to never do that again. The old racks came out; the new ones went in. Ten seconds. On to the next embarrassment...

the chief of the house(not me) did not let the oven finish self cleaning process and that's why this happend.So for everybody - let it finish you'll get no trouble.But repair itself was easy.1-open the oven and take a racks out; 2-unscrew a support of the element on back wall(2 screws);3pull of the wall and unscrew back panel(5screws);4-unplug connectors and pull the element out of the oven.5-installation is the same but backward 4 to 1.It took me...think less then 4 minutes (I went for a beer).DIY and U save a tons.And BTW those guys from Part Select - excelent service.I'm glad that I found a website like that.It's all ready in my favorites.Thanx guys for quick and very good service.It came what I order and it came in 2(two)days.Keep in touch

The draw pictorial was not very clear. I orderd the two rear supports for the over storage draw, not sure they were correct.
They were correct and the design had been upgraded to add strength to the support.
The draw is now operational..better then ever.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

took of the back panel with a nut driver,pulled off the wires one at a time ,put them on the new switch in same position as the old switch.removed old switch with a screwdriver ,screwed in new switch,replaced back panel,put on switch knob

The heating element in my electric oven cracked, I had something boil over onto the element, cracking it to the point of it sparking. First time I had ever seen this before. The appliance repair shop was going to charge me a small fortune to fix this so I ordered the part online, which it was 10.00 cheaper from here than from any other site. It got to me quickly and took me less than 15 minutes to repair and everything works great. All I had to do was unbolt 2 screws with a ratchet, unplug the element, plug in the new one, and bolt it back up and I was done!

My oven bake element melted one day. I had my husband replace it and for a short while it worked. Then it quit but then our broil element would not shut off. My husband said that it might be the heat sensor. We checked here in town and that element cost over $80. Since we have order from Parts Select before we decide to do so again. When we received the heat sensor my husband replaced it taking out the original heat sensor. This did not work as the broil element still would not turn off. I call the repair man and I found out that the initial melt down of the bake element also effected the main circut board that had to e replaced.

Removed the broken socket, and replaced with new one.

1) Remove the door from the oven.
2) Remove two screws from top oven face of door.
3) Flip door over
4) Remove 3 screws from bottom edge of door
5) Lift front door half from inside door half.
5) Remove 5 screws retaining the glass
6) Replace glass assembly and re-assemble door.

Removed back panel screws, removed back panel, removed screws of the control board, remove control board, heated glue and tore off plastic face plate, placed face plate on new control board, installed new control board, moved wires from old control board to new control board, test out oven, reinstalled back panel

First turned off power at breaker box. Pulled stove out to remove the half dozen hex screws on the back panel.(some nuts were stripped)Removed old oven sensor inside oven held by one hex screw and replaced it with the new part. Oven works great now! Repair job was done by husband Mike.

Removed the screws holding the back in place, then pulled off the control knob and removed the two screws holding the infinity switch. Swapped the leads from the old to the new switch and reinstalled everything. Worked like a champ!

Some of the original TO-9 switches were fused by the heat. I made them functional again with a cutter on a rotary tool, but to make the repair properly, I ordered the new control unit and the faceplate graphics. Note the guide tabs at the bottom and right edges when replacing the graphics. Don't plan on reusing your old graphics (unless you are a wizard at removing the very strong adhesive).
To gain access to the part, remove the 2 screws (part 715) in the bottom of the control assembly with a stubby screwdriver. Using a nut driver, remove the two screws (part 1000) on the back at the corners, being careful not to drop them behind the oven. Pull out at the bottom, then move the whole unit toward you. Note the position of the wires. A digital photo can help here. Remove the wiring and 4 screws holding the clear plastic TO-9. Put the screws in the new unit in the same holes and rewire. Put the assembly in place top-first and align the screw holes. Finding the same thread placement for the lower screws can be tricky, so start them gently.

When we moved into our new home I discovered that the oven that came with the home did not have any racks in it. I ordered these racks because they said they were compatible with Hotpoint ovens. However, when the racks arrived they were just a tad too wide to easily slide in the oven. With a bit of force my husband was able to shove the racks in. Luckily I don't cook enough to care if they are moved again because I don't think they'll come out easily.