Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven door hinge would not allow door to open completely
removed oven door, removed drawer under oven, removed three screws holding hinge assembly, unhooked spring from hinge arm, inserted new hinge arm, attached spring, positioned hinge assembly and replaced screws, reinstalled drawer beneath oven being certain that no pot handles interfere with the hinge spring loaded arm, reinstall oven door.
first open oven door a couple inches and slide door up off hinges, then removed storage drawer to gain access to hinge spring, remove hinge spring with pliers noting which hole spring was attached in.then remove three screws from hinge and installed new hinge put three screws in attached spring back and put storage drawer in and oven door back on.
Turn off power at the circuit breaker before working on electric thing.
Removed oven door and shelves for free access to element. Unscrewed the old element, pulled it out, removed the clips and removed the element. Reversed these steps to install the new element. Tested the element to ensure it worked.
Really easy. 1) Pulled up on oven door and removed it. 2) Removed lower drawer to access springs. 3) Pay attention to which hole the springs are attached under the oven. 4) Remove spring with Needle Nose Plier. If you remove by hand, the spring will likely cut your finger....like mine. 5) Unscrew 3 screws of old hinge assembly. 6) Reverse process when placing new assembly in place.
insulation replacement due to cooking oil spillage
raised hood, removed four screws that hold the top plate. placed in new insulation and replace top plate. ran oven at 500 degrees for 20 minutes. all OK.
Safety first: Turn range circuit breaker to off position. Turn a surface unit [burner] to the on position ,if no light exists power has been removed. Turn surface unit to off position. To remove bake unit. With a 1/4 socket driver remove two self tapping screws and gently pull out on the bake unit until you can access the slide on terninals. Careful lenth of wire is limited. Remove slide on terminals two each [2] . Install new bake unit in reverse order . Restore power
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires,held wires one at a time so tehy wouln't slip back into rear holes in oven, slid off connector tabs and pushed on to replacement unit...)
Bake Element went out..flamed out pretty big light show when it happened
The job went over without a hitch, only probably didn't get the correct part first go around, but after getting the right part everything went very easy..Just a couple of screws where the elment goes in and 2 wires to plug back into the new element, after that everything was good to go!!
1. Turned off electrical breaker for range. 2. Removed the two hex head screws that hold element in place. 3. Pulled element out and unplugged the two electrical connectors. 4. Attached connectors to new element and attemped to push element back into the opening. It would not go in all the way. 5. Apparently some of the insulation had fallen down and was blocking the area where the element slides in. 6. I used a long thin screwdriver inserted into the two holes to push the insulation aside. 7. The element was then able to go in all the way. 8. Replaced two hex head screws. 9. Turned on range breaker. 10. Turned on oven. Works fine.
I tapped the screwdriver with a hammer lightly on each of three screws to loosen them. I checked to see the position of the spring on the hinge. I then removed the hinge, put on the new hinge and placed the spring in the exact same position. The door works very good. The hinge replacement was a no-brainer.
first i removed the two screws that hold the element in place. then pulled the element out about 3 inches and disconnected the two wires .then i connected the two wires and pushed thebake element back and replaced the two screws.then i put the circuit braker back on and tested the stove and it worked great. very easy to do.
Shut of circuit breaker. Removed two screws with socket set . pulled element out about three inches, disconnected and held wires in place with clip type closepins. pressed connections onto new element , secured screws and presto... All too simple and in less then 15 minutes. Reading previous reviews was quite helpful
first husband removed the bolts unplugged old element wires -plugged in new element wires and but in bolts - unfortunately the oven still doesn't work not sure if element is bad or wiring, need professional help