Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
burner wouldn't heat up
pulled out the stove,,unhooked the power cord from outlet. I then pulled the control knob off and removed the the six screws from the back panel. I then removed the two screws the were under the knob and removed switch from panel..I unhooked the wires one at a time and rehooked them to the new switch,,pushed the switch back in the panel and installed the two screws. The knob was different from the shaft on the new switch so I took my dremel and contoured the shaft to fit my switch. I plugged the stove back into the outlet and it worked perfect..
Inner glass of slide in range was cracked needed replaced
Removed door from Oven. removed screws from several components comprising the door and separated pieces. Removed broken glass. Prior to putting back together I took advantage of the convenience and used oven cleaner to clean inner portion of door. Installed new glass. Reassembled door.
I knew the lens (which also holds the light) was broken. I also ordered the light. I flipped the circuit breaker, raised the stove top and removed the 6 nut-head screws holding the cover plate. A nut driver would have been helpful, but I got by with a 6" crescent wrench. I removed the cover. I unplugged the two wires from the old light and plugged in the new one. I inserted the new lens and slipped the light over it. I flipped the circuit breaker on to make sure it worked. After flipping the circuit breaker off, I replaced the cover plates and the screws and lowered the stove top. I flipped the circuit breaker on. It worked!
Burner control was erratic. Sometimes it worked, sometimes it didn't.
First pull knob off switch. You may need a small screwdriver to gently start it. I then removed two screws, one in each end of control panel. Then rolled the panel up and out, as it is kind of hinged in the back. Removed two screws from switch front,layed it to the side and installed new switch. Removed wires (there were 5) one at a time with needle nose pliers, and placed on new switch. Replaced panel screws and was finished. Easy fix, quick delivery of part, I have used Partselect in the past and will continue.
The customer service rep was brilliant in finding the right part number! It was sent the following day (with email to let me know) The part itself was just exactly like the old one. I simply turned off the power, removed the 2 metal screws and unplugged the broken element. The new one fit properly and works like a million dollars. For about $50, you made me look like a hero in my own house! Thjank you
Turn off the power to the stove at the circuit breaker. I then loosened the two screws at the rear of the oven and gently pulled the heating elements toward the front of the oven. I found that if I worked the element in a circular motion, it was easier to remove. Once I pulled the element out far enough where the wire connectors were exposed (about 5 - 6 inches), I pulled the wire connectors off the element and reattached to the new element before reversing the whole process. After everything was back in place, I turned the circuit breaker back on and tested the oven, which worked perfectly.
First, I cleaned all the glass from the stove. then I inserted the replacement glass into the slots and screwed the bolts back into the stove. It took me about 1o minutes to do repair. It waS VERY EASY..
We had to take the back off the stove and disconnect the old element. One side had bad wiring. we had to repair the wires and inserted the new element. The job would not have taken so long if there were any kind of instructions.
i slid the oven out unplugged it !! , removed back cover with a nut driver, removed the two retaining nuts from the old bake element ,opened oven door removed two nuts that hold bake element to the back of the oven , installed new bake element then attached wires in the back of oven to the new element re installed retaining screws inside oven , check to make sure screws that hold power cord wires to the over are TIGHT !! i then installed rear cover then plugged in the oven it worked great !!
The bake element caught on fire. I needed to replace the burner..
All I had to do was just unscrew the bolts,pull out the old one, and put the new one on its metal clips and then rebolt.So easy and I know I would have had to pay much more then what I did for the part..This place is super.I ordered my part one day, and it was there the next...Sandy
Instead of flipping circuit breaker, we pulled the oven away from the wall and unplugged it. Used socket wrench to loosen screws of bracket holding old element onto the back oven wall, then gently pulled element until connecting wires appeared. Removed the 'clips' attached to the old element prongs and discarded old element. Reattached the 'clips' to new element prongs, then gently pushed prongs into back into oven wall until the bracket was flush with the wall. Used socket wrench to screw and tighten the bracket into place. Plugged in the oven and tested the new element to make sure it worked. The whole process took only a few minutes.....it took longer to clean the oven before installing the new element.
Removed oven racks and took the opportunity to clean my oven. Then removed the two hex head nuts holding the burner assembly in place. I slid out the burner (very slowly) hoping the connectors were intact and that there was enough lead wire to make for an easy repair. Yes... there were 2 inches of lead wire. It took a couple of minutes to swap out the parts and... success! Don't forget to turn off the circuit breaker before starting repairs.
