Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
replacement of switch WB23K5052 with switch WB24X29364
Remove ten screws that attach top then remove top. Remove four screws holding switches in place and lift for access. remove two screws from switch. Record wire color for positions P L1 L2 for proper positioning on replacement switch. One wire was to short so had to make a two inch extension to complete the hookup. Reassemble and the burners work as original.
Repair was slow, due to replacement part was incorrect. Original part had two spring loaded spacers, & holes for them to sit in. The replacement part did not have holes. I was able to drill two holes to make it work.
Turned off power. Opened range door, removed 2 screws that held top in place. Took a photo of the existing wiring for reference. Removed old burner. Be careful with spacers & springs. If dropped, they will be hard to locate in the insulation. Replaced wiring connectors & verified proper location with photo. Closed cover, replaced 2 screws & turned on circuit breaker.
There are 18 sheetmetal screws not 8 The GE SREWS HAVE AN INTEGRATED WASHER which causes the philips head to STRIP these needed to be drilled out!!! The glass top was GLUED to the sheetmetal box and did not come off without a fight
I am very impressed by your service and company. My order arrived in less than 24 hours. It was a perfect match and is currently in service. I am very satisfied with the entire experience and will use your company again.
I simply opened up the cooktop with a screwdriver and disconnected the wires to the affected burner. After the part arrived, I reconnected them. I had to swap over two brackets from the old burner, so don't throw it away until the new one arrives. It went back together very easily and worked immediately.
Two stage burner was not working on the outer part of burner.
Locate breaker box and turn off breaker to stove. Removed the two screw in front that hold the top in place. Raised the top and supported it with the box the new burner came in. Removed two screws that held the burner in place and the 5 wires one at a time an installed them on the new burner. Put new burner in place and installed two mounting screws. Reinstalled the two screws in the front to hold the top in place then turned the breaker back on and tested burner. Worked great. Received part in 2 days.
Followed directions that I found on the internet and it was easy to remove the old burner and replace it with the one I ordered from you. There was no problems at all.
The age of the system resulted in the cook top being heavily stuck by food-stuff to the range surface. The result was a twisting of the top when breaking it free. It caused the cooktop (a $500+ part) to crack diagonally across the whole surface. Thus ended the quick do-it-yourself process, and out to buy a new range. Parts-select was very good about the return process of the un-used and un-opened burner element.
Switch did not function, boiling water spilled onto cook surface , dripped inside switch.
Raised cooktop......took 8 screws from trim plate and cook surface off.....removed 4 more screws off switch mount bracket, removed 2 screws from switch and mount bracket ( switch now free) ...pulled off wires and connectors one at a time, and put the wire on corresponding new switch location.... Took a total of 30 minutes.... Cleaned cooktop surface too! Cautions...don't tighten ANY screw too tight, as stripping will occur.
The part arrived much sooner than I anticipated. The job was a little harder and took a little longer for me because I'm not good at repairing things. I usually have to call someone. However, I followed the step by step instructions that were provided both on the website and with the mailed item and had no problems. The instructions were clear and easy to follow. The tools needed were very basic - all of which I had on hand. If I could do it - anyone can.
Getting to the control switch was the hardest. Handling our 35" cooktop was tricky. The rest went fairly easy. Just make sure you make a diagram of the colored wires and where they go on the switch. We had to expand the holes in the switch a little to get the old screws lined up.. Putting the cooktop back together was easy.