Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Main burner (right front) always on high
Turn off breaker. Lift cook top from counter. Remove perimeter screws from glass cook top and remove glass. Remove screws attaching control. Replace control and leads. Note: 4 of 5 lead attachment marking points matched old control - I had to guess the fifth. "P" on old was attached to "PC" on new. Attachment points on new were configured differently from old. The leads were just barely long enough to reach. Replaced perimeter screws and cooktop.
Large right front burner would go to high without turning the temp up.
1. Turned of circuit breaker to stove. 2. Take two screws out of control panel, and lifted it up. 3. Lay panel on side and removed knob. 4. Flipped panel over and take several pic for reference of each wire and location on back of controller. 5, Flipped panel back over and take needle-nose players and unhooked each wire tab on back of controller. 6. Flipped panel back over and take two screws out that hold controller on front of panel. 7. Flip the panel back over and remove the old controller. 8. Position the new controller in the panel and install the the two screws back to secure it to the panel. 9. Attach wires back to new controller based on your pic taken. Verify correct location to pic. 10. Attached panel on back of stove. Make sure all wires are secured inside of the control panel. 11. Turn circuit breaker back on and verify the burner is working correctly.
opened oven door and removed two 1/4 " screws from range top. lifted range top and propped open like a car hood with a 1" diam dowel rod. marked on new element the wire color locations from old element and removed wires. removed the two small screws and clips that hold the element to the range top and removed element. Matched where the mounting screws locate to the new element. Installed new element in reverse order.
Remove the top back panel to expose the switch. Remove the switch knob & mounting bezel and then unscrew the 2 mounting screws from the front. Replace the wires one by one and follow the enclosed directions in the event that this is an upgrade for an older switch. Remount the switch from the front and replace the back panel.
replacement of switch WB23K5052 with switch WB24X29364
Remove ten screws that attach top then remove top. Remove four screws holding switches in place and lift for access. remove two screws from switch. Record wire color for positions P L1 L2 for proper positioning on replacement switch. One wire was to short so had to make a two inch extension to complete the hookup. Reassemble and the burners work as original.
Repair was slow, due to replacement part was incorrect. Original part had two spring loaded spacers, & holes for them to sit in. The replacement part did not have holes. I was able to drill two holes to make it work.
Turned off power. Opened range door, removed 2 screws that held top in place. Took a photo of the existing wiring for reference. Removed old burner. Be careful with spacers & springs. If dropped, they will be hard to locate in the insulation. Replaced wiring connectors & verified proper location with photo. Closed cover, replaced 2 screws & turned on circuit breaker.
I am very impressed by your service and company. My order arrived in less than 24 hours. It was a perfect match and is currently in service. I am very satisfied with the entire experience and will use your company again.
I simply opened up the cooktop with a screwdriver and disconnected the wires to the affected burner. After the part arrived, I reconnected them. I had to swap over two brackets from the old burner, so don't throw it away until the new one arrives. It went back together very easily and worked immediately.
Two stage burner was not working on the outer part of burner.
Locate breaker box and turn off breaker to stove. Removed the two screw in front that hold the top in place. Raised the top and supported it with the box the new burner came in. Removed two screws that held the burner in place and the 5 wires one at a time an installed them on the new burner. Put new burner in place and installed two mounting screws. Reinstalled the two screws in the front to hold the top in place then turned the breaker back on and tested burner. Worked great. Received part in 2 days.
Followed directions that I found on the internet and it was easy to remove the old burner and replace it with the one I ordered from you. There was no problems at all.
The age of the system resulted in the cook top being heavily stuck by food-stuff to the range surface. The result was a twisting of the top when breaking it free. It caused the cooktop (a $500+ part) to crack diagonally across the whole surface. Thus ended the quick do-it-yourself process, and out to buy a new range. Parts-select was very good about the return process of the un-used and un-opened burner element.
Switch did not function, boiling water spilled onto cook surface , dripped inside switch.
Raised cooktop......took 8 screws from trim plate and cook surface off.....removed 4 more screws off switch mount bracket, removed 2 screws from switch and mount bracket ( switch now free) ...pulled off wires and connectors one at a time, and put the wire on corresponding new switch location.... Took a total of 30 minutes.... Cleaned cooktop surface too! Cautions...don't tighten ANY screw too tight, as stripping will occur.