Models
>
91133255590
91133255590 Kenmore Cooktop - Overview
Sections of the 91133255590
[Viewing 3 of 3]
Keep searches simple, eg. "belt" or "pump".
Surface Burner Spark Electrode
PartSelect #: PS231276
Manufacturer #: WB13K18
This part helps your burner ignite and produce flame.
$41.95
In Stock
Screw
PartSelect #: PS271689
Manufacturer #: WH2X930
This screw is sold individually.
$12.22
In Stock
Porcelain Burner Bowl - Medium/Large
PartSelect #: PS244322
Manufacturer #: WB31K5092
Sold individually.
$29.85
In Stock
Burner Spark Module - 120V 60Hz
PartSelect #: PS231281
Manufacturer #: WB13K25
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
No Longer Available
Foam Rubber Tape
PartSelect #: PS11726663
Manufacturer #: WB02X26088
This is foam tape and it is usually used in conjunction with your range, specifically on the cooktop. Its purpose is to help seal the edges of the cook top to the counter top. Another of its functions...
$39.82
In Stock
Gas Pressure Regulator
PartSelect #: PS2337785
Manufacturer #: WB19T10078
This comes set from the manufacturer for Natural Gas. It also includes the conversion to Liquid Propane.
This valve automatically cuts off the flow of gas at a certain pressure.
$54.42
In Stock
Single Liquid Propane Orifice Spud - Medium Burner
PartSelect #: PS240769
Manufacturer #: WB28K145
Sold Individually. Order quantity needed.
No Longer Available
Burner Drip Bowl
PartSelect #: PS244320
Manufacturer #: WB31K5090
This black burner drip bowl is sold individually.
No Longer Available
Ignition Spark Switch - Rear Burners
PartSelect #: PS236639
Manufacturer #: WB24K5083
$26.53
In Stock
Questions And Answers for 91133255590
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 91133255590
[Viewing 2 of 2]Will Not Start
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Top four burners on oven would not light without using match
Really simple..Opened the top of the oven and followed the four wires hooked to the igniters on the burners to the back of the oven. Unscrewed top section in back of oven. Found spark module screwed to uppper back of oven on right side. Used a nutdriver to take a few screws out of upper back of oven. Unscrewed spark module from oven. Ther
... Read more
e are six wires - four to the burners and two to the power supply....Wires are attached by connectors so didn't have to do anything but pull the connectors off the old spark module one at a time and push them onto the new spark module matching postion of each wire. Screwed spark module back onto back of oven. Screwed back section of oven back onto rear of oven, and that was it. Works perfectly. Saved more than $100 for service call and whatever elevated price they'd charge me for the spark module.
Read less
Parts Used:
-
David from Logansport, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
62 of 77 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner igniter needed to be replaced
Assumed the entire top of the range would have to be lifted off. Removed the three screws inside the top of the over door and then noticed the two screws holding the dish around the burner. They were tight and required WD-40 and then a sharp tap and came off.
Important: Notice the direction your old igniter is plugged into the w ... Read more ire. It is not clear and can go on either way.
Important: Notice the direction your old igniter is plugged into the w ... Read more ire. It is not clear and can go on either way.
Read less
Parts Used:
-
Thomas from Bloomsbury, NJ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
37 of 63 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spark was present in only two of four burners
Repair was quite easy. Remove four screws and lay back sheet metal panel. Transfer wires from one module to the other and then put new module in place. replaced the sheetmetal panel. Spark now presen at all burners. One small thing worth mentioning. Each burner has a gas distrubution cap and that cap has a small hole to the spark cav
... Read more
ity. One of these was pluged with grease and that kept the burner from lighting until this hole was cleared.
Read less
Parts Used:
-
Paul from Maurertown, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
11 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!