Models > 9112WUA > Instructions

9112WUA Magic Chef Oven - Instructions

All installation instructions for 9112WUA parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 9112WUA
181-195 of 203
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven would not Light

  • Customer: Dan from Clifford Township PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Take off oven door, remove racks, lift out bottom plate of oven, remove deflector shield, unbolt old igniter gently fish out the wire and plug from the back of the oven. Unplug and replace with the new igniter. re-assemble oven.

slow to get to temp and slow to light

  • Customer: Michael from Hartland WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the directions on the video. Very easy to do.

Light burned out in upper oven

  • Customer: Shirley from Las Vegas NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Screwed in light bulb and glass protector

We could not get oven to reach the set temp.

  • Customer: Janet from Hesperia CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My son-in-law unscrewed the front panel AFTER shutting off the power to the oven. He located the thermostat and easily replaced it, then screwed the front panel back in place, turned on the power and we like the results. The oven reaches the desired set temperatue.

Old thermostat knob broke & needed a replacement

  • Customer: Daniel from Willard WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Nothing to it. Took only a few seconds. Just slipped on the new knob and it was good-to-go!

Replace an old igniter

  • Customer: Jacob from Agoura Hills CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Make sure power to the oven is disconnected. Remove all shelves. Partially open the bottom door and yank it out so it is out of your way. The igniter is next to the back and upper wall of the oven inside the lower (broiler) compartment. The igniter is held by two screws which I opened using a 5/16 or 8mm nut driver. After removing the two screws, remove the back plate using a regular phillips screwdriver. Next, pull out the two igniter wires until the connector comes out. Pressing the side tabs disconnect the igniter from the connector. Connect the new igniter. If nesessary, replenish some of the insulation with new insulation that arrived with the new igniter. Push excessive igniter wiring back, remount the backplate using the phillips screwdriver. Remount the new igniter using the nutdriver. Remount the bottom door. Put all shelves back. You are done.

Ignighter comes on but gas will not

  • Customer: Wayne from Vacaville CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
To replace Gas valve, turn off gas to oven and shut off electrical. Remove all oven bottoms (lift out)access to gas valve is in back of broiler section. Remove cover over gas valve(2)screws, remove gas line attached to gas valve, remove wires from gas valve remove (3) screws from mount holding the valve. Pull valve assembly out and remove valve from mount. Install new valve in reverse order.

Oven Would not Light

  • Customer: Neville from Lithonia GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove door. Disconnect power supply from the range.Remove shelves.Remove burner and disconnect power from igniter.Remove bad igniter and replace with new one,reconnect igniter to power supply. Replace burner and all parts that were removed.Re- connect appliance to power source. Range is ready to be used.

Oven would not ligth, igniter did get red.

  • Customer: Fred from Juneau AK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I replaced the igniter, several people on this site agreed that this is the problem and they where rigth.I t was an easy fix. I live 60 miles from the next town and repair shop. I am out in the Alaska bush and can only get to my place by boat or by floatplane. Thank you all you self fixers for your help.

The oven would light, but the flame was very small and it took 30 minutes to preheat.

  • Customer: Bradley from Louisville KY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watch the video, it's too easy and best of all, the part fixed the oven!

heating was suddenly high and constant

  • Customer: freddy from duncanville TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Changed out the thermostat, very easy to do. The instructions were the same as I read on this site on a similar fix. HOWEVER, even after making the thermostat change, the heat did not regulate or adjust. Not sure if part is bad, or something else could be the culprit? but if not thermostat which regulates this, what could it be? I'm very impressed with PartSelect as a company and their website is great, but i'm baffled as to this ongoing problem.

Bulb replacement

  • Customer: Judith from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pulled down the wire around the glass cover...released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Oven Failed to light

  • Customer: Mark from Middletown NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Once I noticed the oven failed to light, I checked the igniter and saw it was glowing. At that point I did some research and found that the igniter could still be bad even though it glowed. This was the most common cause of ovens not lighting. A bad igniter will not glow as bright as a new one. An igniter had to draw a minimum of 2.8 amps in order for the safety valve to open and supply gas to the burner. After checking the safety valve with an ohmmeter, I found it to be good, so I ordered a new igniter. Once I received the new part , it took about 20 minutes to install.

Two mounting screws were bonded from heat and stripped the threads.

  • Customer: Donald from Dixon IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Replaced stripped screws with 632 by 3/8 bolts and nuts. Your video helped with the rest of the installation.

igniter would glow but oven would not light

  • Customer: Roberto from New York NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug power cord to oven.Remove lower panel from inside of oven to access flame rail cover.Remove wingnut from cover to access flamerail and igniter.Using phillips head screwdriver,remove 2 screws from lower access plate located at rear of oven to access igniter wiring.Disconnect both wires, then using a nutdriver,unscrew and remove igniter from flamerail.To install, simply reverse instructions.It was extremely simple and fun to do.But most rewarding of all was the sense of accomplishment from doing the repair myself not to mention of course the money i saved not having to call a technician. Thanks guys!
All Instructions for the 9112WUA
181-195 of 203