Models > 8ET15GKXJT

8ET15GKXJT Maytag Refrigerator - Overview

Get Parts and Repair Help for 8ET15GKXJT

If you know the refrigerator repair part you need, you can browse the list of all parts on the 8ET15GKXJT, or you can search by name or part description. You can also find your part by where it is located on the 8ET15GKXJT by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for 8ET15GKXJT parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$126.87

Ice Maker

This replacement ice maker mechanism does NOT come with a cover, a wire harness, or the mounting hardware. Must be ordered separately.

$2.70

Screw

Sold individually.

$2.70

Screw

This screw is sold individually.

$8.27

Shelf Retainer Bar End Cap

Sold individually.

$7.28

Light Rocker Switch

$3.96

Crisper Drawer Shelf Support

This crisper drawer shelf support is used for many refrigerators.

$31.14

Condenser Fan Motor Kit

This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a blade mounting nut, and a cushion. This part provides forced-air ...

$18.32

Water Fill Cup and Bearing

$47.27

Single Outlet Water Valve

This valve has a 1/4" tubing inlet connection. When energized, this part releases water from the supply line into the ice mold.

$55.91

Defrost Timer

This refrigerator defrost timer will cycle for twenty-one minutes after every ten hours of run time. The defrost timer acts like a clock. It continually advances and alternates between activating the cooling cycle and the defrost heater.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water overflowed ice maker turnning ice bucket into solid mass of ice

  • Customer: Harry from Grand Ledge MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 185 of 255 people found this instruction helpful
My ice maker has been shedding its non-stick coating for over a year. Within the last month of so, it started pouring water into the ice bucket below, turning it into a solid mass of ice. So I purchased a new ice maker assembly. I encountered two problems not mentioned in the 21 or so do-it-yourselfer repair stories that precede this one. First problem: o... read more

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 76 of 79 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more

cocktails running out of ice

  • Customer: Craig from Westminster CA
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 49 of 54 people found this instruction helpful
filled both ice cube trays up with water and placed in the freezer.. within hours my ice oproduction was doubled! no more warm cocktails : ) read more