7WDT770PAYW1 Whirlpool Dishwasher - Instructions

Fast,smooth,easy.

If your are just a tiny bit "handy", you can do this job in about 30 minutes for $30. The rubber gasket comes off very easily from its location, just pull it off, than, using a small piece of wood, I used a shim, insert the new gasket in, an inch at the time, all around the frame. No more leak, and probably over $150 savings. A plumber or repair man would have charged $90 just to drive to my house, plus part & labor.
Thanks to PartSelect too, the part was delivered rapidly and the all ordering process was painless.

laid dishwasher on its side and unscrewed element. returned unit upright & replaced element. reversed process and reinstalled unit under cabinet

Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.

Disconnect power Pull out dishwasher. Turn it 45 degrees to your right. Turn it on its side. disconnect the connections to the heating element {2}. Remove bolts, remove element. Install new element and tighten bolts. Reconnect electrical connectors. puch it back in place. reconnectPower your done

My wife hired a local repairman when the right side spring cable broke (I was out of town). He took two hours to fix it (and two appointments). The door would then pop open when running. He came back and replaced the latch. Problems persisted. I then ordered new hinges and replaced both in half hour or so. Would recommend doing all of these repairs yourself. None of these repairs are that hard and definitely not worth paying hundreds to do it. Trickiest part is pulling the dishwasher out from the counter without impacting the electrical or water connections. Disconnecting the power is important on all repairs. When you take the screws out of the door to get to the hinges, make sure you have a helper just to hold the door up while removing the last few screws. The left side hinge was really bent (when the right side spring cable broke) - caused the door to be out of square and thus would not effectively close. This was obvious after a 5 minute search on this this and other repair sites. Process that I used: 1. remove screws from both sides holding dishwasher into counter (may have screws into countertop as well). 2. turn off power, 3. pull out dishwasher far enough to see hinges and springs (careful of connections), 4. remove front door screws, 5. take off front panel, 6. remove spring cables (pull cable taut and remove "hook" from hinge)., 7. unscrew two screws holding hinge to door, 8. bend metal fingers around hinge pin to be able to remove hinge., 9. attach hinge in opposite path. 10. repeat on other side (if necessary), 11. reconnect things in opposite order...test door prior to reattaching door panel. Make sure you level the unit with the adjustable feet. Make sure screws in sides of cabinet aren't too tight as it can take the unit out of square pretty easily...

I needed to replace the black access panel on my Whirlpool dishwasher (model WDF520PADM7).

By following the instructions in this short video (https://www.youtube.com/watch?v=995mtdO7rQg) , I was able to complete the replacement in under 10 minutes. You'll need a flat-blade screwdriver. The Retainer Clip - Black can be a little tricky to position into the opening, so have patience.

Keep in mind that the Retainer Clip - Black only contains ONE clip and so you must make sure to order TWO Retainer Clip - Black from PartSelect.

Turned the dishwasher in its side. Used the video step by step. This is why we purchased from this site

I followed the YouTube attached with PartSelect email invoice to fix it. I am very happy PartSelect sent repairing video instruction and took me less than 15 minutes to get it done. Awesome!

Ordered a new pump (after a online diagnosis). Followed the instruction video on the website...also took the time to replace the discharge hose due to residue buildup...tested dishwasher (one cycle). Slide dishwasher back into opening....DONE. Works perfectly. THANKS

The old filter simply unscrews and the new one screws in.

removed and installed cords with screw driver

Pulled dishwasher out of compartment, removed all parts underneath. removed inner parts, removed pump assembly. Installed new pump assembly and grommet. Reassembled in reverse order, test ran and unit was operating normal and no leaks.

went to utube

Originally I ordered the rack stop clips but realized I needed the whole upper rack repair kit. It entailed pulling off parts and popping new parts on. Very easy and simple.