7MRGX4634MQ0 Roper Dryer - Instructions

The intermittent drying of my gas dryer was the tricky issue for me to pin point. Your web site said 53% chance thermal fuse and 21% "M" series new style coil kit. Ordered both and delivered in less then 18 hrs, impressive! The old fuse tested out OK but I replaced it anyway. Replaced the coil kit (using a step by step video on another web site) in about 15-20 min. Working great now and fixed for under $49. Happy in Milwaukee.

I watched your video and did the job,really no problem. I also cleaned out all the lint and dust will the drum and front were out.

Watched video on the website and saw how easy it was so ordered the part. Part arrived quickly and had dryer up and running within 15 minutes. Good part good price and good intructional video

Fortunately this is an easy diagnosis and easy repair. The great PartSelect instructional videos are a HUGE HELP!!

remove back of dryer and install new part

Took 12 screws off the back. One screw for the fuse. $9.32 and 30 minutes and we're back in business!

Followed the instructions that came with belt everthing went just fine.

I ordered the maintenance kit because it was recomended for my application and the symptoms my dryer was exhibiting. However this kit did not apply to my model. My model contained 4 drum rollers, only 2 came with the kit, and the idler pulley setup was completely different. I should have pulled the dryer apart first to compare pictures to the actual parts. No big deal, prompt refund after a quick phone call to Parts select. I was able to fix my idler pulley with a couple of new nylon washers and a new snap ring to hold it in place. Whirlpool cabrio wed6200sw1.

I replaced the entire motor in the dryer and the belt while I had it open and it is working great! I just watched the short video on the site to learn the tricks and did it myself.

Followed video, very easy installation. Unfortunately, the new starter switch does not stay on either so we still have not resolved the problem.

First removed and checked the ignighter. It was fine. Next I located the schematic drawing and discovered that the burner, ignighter, and flame detector were all operated by one simple 110 volt circuit. This circuit did not power up when the dryer was cycled on. I pulled the dryer from the wall, removed the back panel, the vent etc. I then located the operating thermostat and the thermal fuze. The thermal fuze was open. (GOOD NEWS AN EASY FIX!!!) Thanks Guys

Well the video showed us taking off the back. Which wouldn't come off. Welded. Then we could not find the fuse in back of the unit or bottom. The second time we tried we found it in the front. We had to take off the front, bottom cover then we found the fuse. But, it didn't fix the problem. The unit is still on Casual load only. When we push the buttons the other lights light up but goes back to Casual. The unit is clear of lint and still drys but only at the Casual setting.

I watched the attached video that was with the belt I ordered and it took less time to do the repair, then it did to watch the video. The video was very helpful.

Trouble shot to failed motor. Ordered motor and new drive belt. The hardest part is figuring out how the dryer dis-assembles. Follow Parts Select on-line instructions. Also, several good instructional videos on You Tube! My recommendation is to order a new "blower wheel" when changing motor on a gas fired dryer. The heat combined with age bonds the blower fan to motor shaft. It had to be broken off in pieces to remove motor.

Followed instructions that came with the dryer with the exception of the idler pulley which I didn't install because this maintenance kits idler pulley does not match my dryers. Not even close. I would have had to cut or drill holes to make it work. Since I knew it was the rollers that were the problem. Dryer worked great once I was done, but it probably would have been cheaper for me to order the parts individually without the Idler Pulley if I wasn't going to replace one.