Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer would not complete cycle, as I forced the top open when locked
I did the repair just as the video showed, and had no problems at all. the hardest thing I had to do was to move the washer out to where I could get to the back of the machine. Due to the help of the sales rep and the video the repair was very easy
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
washer wasn't spinning after rinsing but the motor was running
I had taken the time to watch videos of this repair so when the switch arrived I knew what I had to do. Removing the screws to get the back cover off was simple as was installing the switch. No tricks here just watch the videos and your all set to do the job
Washing machine would not spin clothes, little to no agitation
Our 5 year old Kenmore washing machine broke. The first symptom was that the clothes would come out completely wet. This was due to no spin cycle. The second symptom was that the washing machine had little to no agitation. The lid still locked shut, there was no odor, and you could hear the machine running.
In the event a machine does not agitate or spin, the diagnostics on this website will lead you to believe that drive hub assembly or shift actuator is the problem. The drive hub assembly is by far the more common repair (the pieces are made of plastic and are designed to wear out). If you are torn, go with the drive hub kit repair. That's what it was.
There were some surprises after carefully watching the how to video. First, the agitator in my machine was very tall and required a socket wrench extension to reach the drive hub nut. This will require two sets of hands. Second, the drive hub nut was stuck to the point where I nearly gave up. WD-40 and degreaser did not work to loosen. I ended up pouring a half teaspoon of powdered soap onto the stuck nut to get more grip on the nut. This, along with two sets of hands, got it loose. Third, calibrating machine was barely touched on in the video but this is extremely difficult, the instructions that come with the part were insufficient, and the videos on the internet are not that good. In the end, I'm not sure that the machine ever calibrated. In essence, the machine is re-calibrated by turning the switch in a specific sequence of right to left. Lights are then supposed to flash. This never did anything. I ended up opening and shutting the lid 10 times in 10 seconds as this was allegedly a way to recalibrate.
Note: 2018 and later washing machines suck because of California and the federal government rules and pressure to make them "green". Well, they don't work that well anymore as a result. Keep this in mind when you vote.
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
6 of 6 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
F7 e1 code
Thought we needed a new shift actuator but after getting the parts and starting the replacement noticed the capacitor had come loose and was banging around under the washer. Found there was a little wire to the shift actuator that was cut probable from the capacitor being loose. spliced the wire back together and replaced the capacitor but not the shift actuator and its been working great. was an easy fix and easy to get to. Didn't need the maytag man when we can get parts from here.
I unscrewed the top panel of the washer. I lifted up the top and used the pint scrapper to loosen up the lid switch and slid it out. I pulled the switch wiring harness out of the rear top of the washer. I slid the new lid switch and wiring harness back through the opening and secured the switch in place. Screwed it back in place. Took less than 15 minutes. I followed the instructions on the video, easy peasy lemon squeezy.
Removed belt cover from bottom of the transmission , remove old belt, clean the pulleys ,and re install new belt. The new belt fits tighter so it did a few time to get the belt fully seated. Re install belt cover.
I watched the instructions on line, and followed them. Completed the parts change with out any problems, but that wasn't everything I had to do to make the washer to work again. I had to clear all the fault codes that were on the machine. Then the washer started working in all the cycles.
Remove the center cover with a screwdriver then loosen the 7/16 bolt with an impact driver socket ccw to remove completely biggest issue is removing bottom cover tried pick tools only thing that was succesful was some dawn dishsoap on the center bolt area to loosen enough to lift up the cover replace the hub part that had worn spline grooves remember to use blue loctite on the 7/16 bolt before re-installing cw to tighten bolt
My spin cycle was running, but spinning slowly and not drying my clothes. The agitator spun quickly like normal, but the basket did not spin fast. It seemed like something was slipping. I checked the belt, but it seemed fine and it was less than a year old. I was afraid that the transmission was going, but there wasn't any grinding sound of gears. Luckily the hub part description said that this could fix the slow Spin cycle. Over all the repair was easy, but pulling the agitator off was very difficult. I've got a strong grip and patience and after about 10 - 15 mintues of yanking on the agitator it came off. Don't try to use pliers as it will damage the plastic agitator. Replacing the hub drive and reassembly went very smoothly. The old hub drive wore out because it is plastic and connects to the metal drive shaft from the transmission. After years of torque, the hub will eventually strip out. Sooner depending on your usage and heavy duty cycles. In case you don't know, your machine might have the service manual in it on the inside of the body taped to the side. Mine helped me run through some troubleshooting steps and component tests to pinpoint to problem. Thanks Parts Select!