7MMSL6955TW0 Maytag Washer - Instructions

went really good, received both parts in less than two days, great service! Video's on line were really helpful and made taking apart and putting back together easier, even though video's were on newer model machines. Would not hesitate to order parts from Part Select again.

Removed housing, using pry bar lifted plate used screwdriver removed wear pads one at a time. inserted new ones and snapped into place. Did not have to remove tub. Be sure pry bar does not slip and you pinch your fingers. Machine works just fine know.

Watched your video and it was right on so helpful it made my job easy.

The washer agitated ok, so I figured it wasn't the motor or agitator. Watching the repair videos, I assumed the clutch might be the culprit. The videos are very good, so I should have taken the machine apart and actually looked at the clutch - it wasn't too bad. Trying to put the new clutch on anyway, I noticed it didn't turn on level. I thought it wasn't seated correct, but it was then I realized the shaft was tilting. This would explain the THUMP, and the grinding must be a gear inside the transmission. As much as I hate to get a new machine, given the tremendous downturn in quality, I think that because this machine is old, it is not worth a $200 transmission. Anyone need a brand new (but test fitted so not returnable) clutch?

Went on-line for help.found parts select website.referred to your service videos.discovered solution to problem.bought proper part.arrived in excellent condition.watched another video for how to install the part.completed repair in about one hour.washer operating back to normal again. this site is a one stop answer/parts shop. thank you .

the tube when spinning the tub would shake so bad the washer would walk away from the wall but it will not happen anymore since I put the new spring on it runs great and this is not my first rodeo. Removed the outer part to timer controls then removed two screws then shell in front came off the body

First I purchaseda new drive coupler and replaced it. Still the drum did not spin. Then I ordered a new clutch but this time when I disassembled the unit I ran power to it after removing the water pump I turned it on and the motor and basket now spun. I found out the water pump was seized so I brought it to my work bench and examined it. When I looked inside I saw a foreign object stuck in the impeller. I took needle nose pliers and worked it out. It was actually a baby's sock from my grandsons recent visit. How it got behind the drum and into the drain hose I have no idea. Once the water pump was freed up, the entire problem was fixed.

I watched the how to video and it was very helpful. I followed all the steps as described although I did not take the cabinet off , I just laid the unit down on the back with a couple towels behind it. the only thing that was a little bit hard was hooking the back clamp on the pump. If you hook the back clamp before putting the pump back on it is much easier.

Your installation videos are the best thing ever!!! Anyone who is mechanically savvy can repair anything following your instructions. Thank you SO much. I watched the video a couple of times, took some notes, and replaced the clutch. Problem solved. So, thank you for carrying a multitude of parts, quick shipping, and for the videos. I can repair almost anything, but your services make it time and cost effective in an era where the mantra is discard and replace.

Followed the instructional film that was included on website.

It was a miracle. We were going to get rid of the washing machine because it made so much noise and rattled the whole house. It also 'walked' across the room with every load.
I simply replaced the wear pads (2 of them were already worn away), and now it is as quiet as when it was new. AMAZING!

Tried to follow videos. Couldn't figure how to raise top. Laid machine on front used pliers to unclip bracket and clips holding hose. Took 10 minutes to work it this way.

Pull the washer out away from the wall and tip back.
I used a small metal ammo box to hold up the washer.
The bottom pump retainer is easy reach and remove with a flat screwdriver. I was able to pry off with my hand.
Replace retainer insert into slots on drive motor and twist.
I used a pair of Channellock pliers to lift retainer while pressing along the
side till it snaped into place.
Remove the support box and put washer back.
Then tip washer forward to reset self-leveling mechanism.

My factory drain hose had a hole in it, that I replaced with a hose from Lowe's. This was my first time doing this, took some time and difficult. I found out after replacing it, that it was not the right fit, as the drum would bounce around during every wash. After 3 months, due to the bouncing of the drum, that house had a hole and needed to be replaced. I chose parts select, and although the specs of the hose listed it as shorter in length than the one I bought from Lowe's, it fit perfectly and fixed my lose drum. I had watched the video on parts select numerous times (swapping out hose) so this was done in less than 10 minutes. I have become a pro at this and it is all thanks to parts select. Thank You!

Ordered drain hose extender. It uses a rubber flange with hose clip to attach to washer's plastic hose. When tightened, the hose clip crushes the plastic hose and crimps it, causing a leak. My solution was to find a copper pipe flange that was the same diameter as the interior of the plastic hose to act as a bushing for the plastic hose. The hose clip could then be tightened without deforming the hose. Worked great with no leaks.