7MMPD6845TM0 Washer - Instructions

as in video

Removed inner cap seal, agitator bolt and them removed agitator. Remove cam kit, installed new kit, reassembled. PS I am a retired appliance tech we ho has done this before.

it went very fast after watching the how to fix video

After about 4-5 years, the agitator cogs or "dogs" will wear out and cause the agitator to stop working-Simply pop the cap off of the top of the agitator with your hands by pulling upwards, remove the plastic cap at the bottom of the agitator-there are 2 plastic ears that you pull up on also with your hand, exposing a 1/2 locking nut. Use a socket and extention to unscrew the nut. Grab the bottom of the agitator with both hands and pull sharply upwards removing the entire assembly. Flip the assembly over to expose the four cogs. Replace with new, and reverse the procedure to reinstall the agitator

After watching the repair video by partselect.com I followed the directions exactly. It turned out to be a piece of cake. I found out that partselect.com has many, many do it your self repair videos on youtube.com. I intend to use them for future repairs. Thank you partselect.com.

Determined based on some Internet searches that the part that we needed was the motor coupling; washer would not spin or agitate. Once I figured out how to removed the cover (by the way, one of the guys at an appliance store told me how to do it), and reviewing the video on your website, I removed the two screws and four clips, dropped the motor, inserted the parts and put it back together - all in about 15 or 20 minutes. It was easy and clean and the washer worked again. Hopefully go for another 5-10 years. Thanks.

went to you tube and watched a video on how to take it apart and replace the clutch assembly.

Remove protective cover and inner seal with gasket from top of agitator. Use socket set with extension to reach bolt in bottom of agitator and loosen bolt. Remove assembly from washer. Take out interior disk and remove broken agitator directional cogs. Replace with new directional cogs. Reassemble parts in reverse order. Easy Peasy,took about 5 minutes.

Popped top cap off agitator, removed bolt, removed top agitator, replaced directional cogs, reinstalled top agitator, bolt, cap. This machine is 43 years young, it's happy again.

Used pliers to help disconnect hoses, unplugged power cord, laid washer on its back, unsnapped two clips holding pump to the motor, lifted pump off, and replaced it.

Popped agitator cap. Used ratchet to remove screw. Pulled off base unit. Inserted cogs into slots after removing worn and or broken cogs. Reinstalled......done!

Took out the fabric softener dispenser. Unbolted the 7/16 bolt and then pulled the agitator unit out. Separated the top and bottom agitator units and knocked out the agitator cam kit. Reinstalled the new cam kit, put the top of the agitator on the bottom unit and reinstalled the whole unit. I then bolted it back in and put the agitator cap on and the fabric softener dispenser on and now the wife is happy again.

I took the Agitator Cap Barrier out of the Top part of the agitator and than screw that holds the 2 parts together. I removed the part that holds the Cogs. I replace the Directional Cogs (dogs) into the holder, replaced the holder into the top agitator, replace the screw, put the new Agitator Cap Barrier in and it now works as good as new!! It took me 3 minutes tops!

After removing the outer shell of the machine, and disconnecting the supply hoses, I leaned the machine on it's back and disconnected the drain line. Then, it was simply a matter of removing and replacing the damaged pump with the new one. The pump is held in place by two easily removable clips. The hardest part of the whole process was making sure the shaft from the motor lines up with the corresponding hole on the pump.

Followed instructions on WEB site, they were very easy.