7MMMS0100VW0 Maytag Washer - Instructions

Well, after resolving Part Select (PS) shipping issues (PS sent me two refrigerator glass shelves instead of a Tub Spring); And as it turns out they sent me the wrong part for the suspension pads, which I have returned for credit. It takes 3-4 weeks to obtain your credit BTW.

Well after removing the cabinet, agitator, wash basket, plastic tub, all 5 springs, & pump suction line, I was able to access the Tub wear pads and suspension pads. As it turns out the suspension pads looked good.
Thank God, as PS had sent wrong parts. I replaced the wear pads, the 5 springs, and reversed the disassembly process. Took about 6 hours.
But washer works fine now, still vibrates, but does not walk across floor any more.

went really good, received both parts in less than two days, great service! Video's on line were really helpful and made taking apart and putting back together easier, even though video's were on newer model machines. Would not hesitate to order parts from Part Select again.

Tried to follow videos. Couldn't figure how to raise top. Laid machine on front used pliers to unclip bracket and clips holding hose. Took 10 minutes to work it this way.

Went on-line for help.found parts select website.referred to your service videos.discovered solution to problem.bought proper part.arrived in excellent condition.watched another video for how to install the part.completed repair in about one hour.washer operating back to normal again. this site is a one stop answer/parts shop. thank you .

the tube when spinning the tub would shake so bad the washer would walk away from the wall but it will not happen anymore since I put the new spring on it runs great and this is not my first rodeo. Removed the outer part to timer controls then removed two screws then shell in front came off the body

The washer agitated ok, so I figured it wasn't the motor or agitator. Watching the repair videos, I assumed the clutch might be the culprit. The videos are very good, so I should have taken the machine apart and actually looked at the clutch - it wasn't too bad. Trying to put the new clutch on anyway, I noticed it didn't turn on level. I thought it wasn't seated correct, but it was then I realized the shaft was tilting. This would explain the THUMP, and the grinding must be a gear inside the transmission. As much as I hate to get a new machine, given the tremendous downturn in quality, I think that because this machine is old, it is not worth a $200 transmission. Anyone need a brand new (but test fitted so not returnable) clutch?

Your installation videos are the best thing ever!!! Anyone who is mechanically savvy can repair anything following your instructions. Thank you SO much. I watched the video a couple of times, took some notes, and replaced the clutch. Problem solved. So, thank you for carrying a multitude of parts, quick shipping, and for the videos. I can repair almost anything, but your services make it time and cost effective in an era where the mantra is discard and replace.

Removed housing, using pry bar lifted plate used screwdriver removed wear pads one at a time. inserted new ones and snapped into place. Did not have to remove tub. Be sure pry bar does not slip and you pinch your fingers. Machine works just fine know.

Watched your video and it was right on so helpful it made my job easy.

First I purchaseda new drive coupler and replaced it. Still the drum did not spin. Then I ordered a new clutch but this time when I disassembled the unit I ran power to it after removing the water pump I turned it on and the motor and basket now spun. I found out the water pump was seized so I brought it to my work bench and examined it. When I looked inside I saw a foreign object stuck in the impeller. I took needle nose pliers and worked it out. It was actually a baby's sock from my grandsons recent visit. How it got behind the drum and into the drain hose I have no idea. Once the water pump was freed up, the entire problem was fixed.

I watched the how to video and it was very helpful. I followed all the steps as described although I did not take the cabinet off , I just laid the unit down on the back with a couple towels behind it. the only thing that was a little bit hard was hooking the back clamp on the pump. If you hook the back clamp before putting the pump back on it is much easier.

After reading everyone elses stories, I purchased all new springs(5), new spring brackets(one of mine was rusted really badly)and all new wear pads(two sets of 3pcs each). The rusted spring bracket was the most time consuming as the screw was rusted into the bracked so I had to drill it out. Other than that, the actual spring replacement was easy. Took maybe 10 minutes. The wear pads were another story. I'm a pretty good mechanic and I had a bit of a struggle getting the old pads out. I used a long, flat head screwdriver to pry them out. Once they were out the new ones weren't too tough to get back in. Took about 20 minutes all together. I stongly recommend watching the video on removing the washer cabinet first. It will save you some time. Acutally, watch the videos on all of the parts to simplify the process. Oh and by the way, all of my washer problems are gone. Well worth my time and $70 in parts. Good web site!

First, I purchased the lovejoy coupling and replaced it, all of the interlocking pins were broken. I suspect that occurred when my wife washed the comforter. Started up the machine and started to smell like the motor was overheating. Also the machine was making a lot of noise (screeching) when it went into spin cycle, so I purchased the clutch. For both repairs I watched the videos and they were spot on and easy to follow. Recommend laying down the washer when replacing the lovejoy coupling, as that was a little tricky trying to do that with the unit upright. The guy in the video must have done that a thousand times to line the up the holes and the pins! Washer is working like a brand new machine!

Looked it up on utube

I am an old woman who is disabled and without any tools or knowledge, but sheer stubbornness and will power, I waited for my tools and other parts to come in, in the mean time I fixed my young neighbors whirlpool washer, well We took top off the nut I had already pre assembled her cam so set it in place of old one put bolt back in place and the top of agitator she says works perfectly now, my parts came in I had nothing to remove as my handicap daughter had already thrown away all the loose parts, I threw away old top agitator, assembled cam and put in place still did not feel tight enough so added seal from other nut!! it worked tight enough, put the inner part back in with new part and soap put the top back on and now works good as new, was disappointed could not put bottom agitator in place, just not strong enough lol well this was my story