7MMGE7973TW1 Maytag Dryer - Instructions

I watched the PartSelect video once before the part arrived. Had the part replaced in under 15 minutes. Very quick and easy.

Went to YouTube It was real easy.

Removed front panel unscrewed the 2 screws on the coil cover. The coil with two prongs had to upside down 3 the prong coil right side up that only way the cove will fit, plug them in re attach the cover and your done

Thank you for the the installation tip I received along with the part. The suggestion of removing the front panel to install the belt made the installation go very smoothly.

I followed the directions on your site. I pulled out the filter on the top of the machine. Then removed the two screws where the filter is located, I am not sure I would have found those screws had it not been for your directions. I then pulled up on the top of the machine by grabbing the sides near the front of the top, it came right up. I then raised it enough to place a broom handle to hold the top up so I could reach the switch. I removed the two screws holding the switch and then pulled the connector apart. I then replaced the switch with the two screws and plugged the connector back together. Removed the broom handle and closed the top and replaced the two screws I removed by the filter. Replaced the filter and started the machine running and opened the door and it turned off and the light came on. It took me about twenty minutes.

Parts came as ordered and in really good time. The valves were very easy to install, just a matter of removing lower housing and the two screws holding in the old valves. The plug and play, no calibration needed and the dryer works like new. Very easy fix and the instructional videos were very helpful. Saved a lot of money doing it myself.

Replaced bad coils

I unplugged the dryer then removed 2 Phillips screws from lint trap. Then I popped the top up on each top corner with a screwdriver. I removed the 2 screws holding the front cover. I unclipped the wiring connection and moved the panel. I took out the old belt, put the tensioned back on then put the new belt around the drum and held the drum up with my shoulder then put the belt through the tensioner and put it on the motor spindle by pushing the tensioner back. I put it back together and it worked perfectly. Your video was very helpful. Job was very easy.

The instruction sheet that comes with the parts is excellent. Follow it and all goes well. Be patient and stay away from the sharp sheet metal edges present in all such appliances !!

Removed 2 screws at the lint filter, unplugged dryer, next I popped the top off with a standard screw driver lifted the top all the way up and secured it from falling back down, used a 5/16" nut driver to remove the top 2 screws holding the face on, disconnected the door switch, pulled the face panel off and set it aside, then I removed the tension pulley on the bottom and took the drum out, unscrewed 2 screws holding the coils removed the old coils and installed the new reconnected the leads to them, vacuumed out the cabinet and motor, inspected all moving parts for wear, including the belt, reinstalled every thing in reverse order, had job complete and ready for clothes in 9 mins, it helps to have your son/daughter hold the drum against the back wall while reconnecting the tensioner and belt.

First I opened the back panel & check the fuse with multi meter tool ( put in ohms & set it in 200K) & the fuse is Ok, try to run the dryer while looking in the flame dock & the burner starts & had a fire till about 2-3 mins. & flame comes off, what I did is I open the front door to access into the gas burner, check gas valve coils with multi meter tool for continuity & found out that one of the coil doesn't have continuity. I ordered a pair of coil that is located on top of the gas valve on this site & unexpectedly it came in the next day, WOW! that's a fast delivery I was very pleased w/ the service, come home from work & installed it right away & it took me 5-10 mins. Put back everything & try to run it & it works properly. So happy with & my wife as we'll, thanks for the great fast delivery.

Had husband of 55yrs.replace the switch VERY SIMPLE!

First and foremost, PartSelect is awesome! I placed the order on a Monday afternoon with regular shipping, and I had the belt Tuesday evening. Total repair involved removing several screws to open the top and front of the dryer, then installing the new belt. Pay close attention to the the dryer seal - make sure this is completely set. This was a very, very easy repair, and it cost me less than $20 for part and shipping! Also, the video on the PartSelect site shows exactly how to make this repair, and was very helpful.