7MMGD0100TQ0 Maytag Dryer - Instructions

My Daughter and I have the same washer and dryer from Maytag. Her felt piece came apart on the lint filter. I let my fingers do the walking and checked which filter went with the dryer and purchased it. When it got here, I made sure it matched up with the old one and just put it in the dryer where it belonged.

I removed the front lower panel and could access the parts easily. This model of dryer was a little tricky as to what needed to be removed to access the parts. It was easy to take off the flame sensor and the therminal gas valve and replace. I watched your video on changing these parts but it didn't help much as the model in your video was newer and the parts were not in the same location on my dryer. the top on my dryer could not be popped up it was held by screws accessed by working from the bottom panels up. It turned out I only needed to take off the bottom kick panel to replace the parts it needed. The dryer works fine and the information,you provided on your website about what parts cause this problem most of the time on this dryer helped me to order the correct parts.

This was by far so easy the instruction Partselect gave me where right on step by step. a repair man was going to charge 75$ just to come out 9$ from partselect. Thank you very much Mike chaplin

Remove front cover to expose internal parts, igniter would glow and gas vavle would click ,but no flame in auto, would light in manual but go out quick. Gas valve coils bad. Thermistor was testing good but I replaced it in case it had anything to do with quick flame shut down. $25 Dryer fixed for $50. Clean out lint in all vent duct work to make sure a clog is not the problem for quick flame shut down as well.

1. Disconnect power cord and remove flexible duct. 2. Tilt dryer back and lean against wall, using folded towel to prevent wall damage. 3. Remove front/bottom panel - 4 screws on front/bottom of dryer. 4. Make alignment marks on internal vent duct where it attaches to vent bottom duct housing. Remove internal vent duct screw (towards front/top of duct) and slide vent duct out back of dryer (duct has to be removed to remove back panel) 5. Remove top panel (4 screws on back/top). 6. Remove AC power terminal block from back panel, disconnecting wire that restricts free movement of terminal block. Remove power cord from terminal block (3 nuts). Remove back panel (many screws). 7. From rear of dryer, gain access to idler pulley spring arm. Carefully note how belt routes around motor pulley and idler pulley (maybe record an image). Release belt from idler pulley. 8. Remove idler pulley triangle retainer (if still on pulley shaft) and remove old pulley. 9. Thoroughly vacuum lint and dust from all areas of dryer, internal duct, flexible duct and duct in wall (as far as possible) while dryer is in disassembled state. 10. Thoroughly clean idler pulley shaft of deposits with cloth. If desired, add very small amount of Park Tools Polylube 1000 to the cleaned shaft. 11. Install new washer, idler pulley and triangle retainer to shaft. 12. Re-route belt around pulley in original orientation. 13. Reassemble rear panel to dryer, terminal block to rear panel, and power cable and internal wire to terminal block. 14. Reassemble top cover to dryer. 15. Insert internal duct back into front vent duct, aligning guide marks, and secure with the one screw. 16. Plug unit in and briefly test, then unplug. 17. Again, tilt dryer against wall and reinstall front/bottom panel and screws. 18. Install flexible duct, plug in power cord and position unit for operation.

First, I replaced the male end which was just two screws and simple replacement of pushing the fastener into the door frame. When finished I noticed the female end was damaged as well. Glad the female part came as well. This required taken off the front trim around the door (four screws - 2 each side) and then the door. The installing of the female end was easy with a little push. The damaged female end was already hanging out so easy to grab and remove. Otherwise I would have had to remove the front panel. Note You need to put the door trim back on before reattaching the door.

The gas would light briefly then go out so the clothes were never heated. I googled the problem and found your website and read a few blogs describing the problem, ordered the coils, popped them in and presto it worked.

This was real easy just slid the latch in front panel and attached to latch assembly to the door. The repair was about 45 seconds.

I replaced gas coils which in my case came as a set and that did the trick.

Pretty easy to fix, hardest part was having to get the screws out of the inside of the dryer to replace the sensor itself. Once that was done it was pretty quick! PLUS super fast shipping on my part!! Was fixed before any repair places even called me back!!

I started by taking the front of my dryer off and cleaned it out. Next i ran the dryer and watched the flame starter circut. The starter circut would work once and then not for a long time but i could see it was tring to light because the iginiter would glow white hot. I then searched online for my model number and found the part select web site. In a few minutes I found a dryer fault description that best fit what my dryer was doing. The part select site should me three parts it might be. I read about what the three parts did on the parts select site. Then by using the process of elimination, with the knowledge I had just learned, I narrowed my suspect parts down to one. The coil for the gas valve must be the problem. So I got my ohm meter and measured the coil resistance and I found that when the coil was room temp it had resistance. But it would get hot after one heat cycle and it would open up therefore causing the gas valve not to open......no heat! I ordered the part and it came in two days!!!! All fixed!

im a car mecanic it was easy

I took the old filter out and placed the new one in the same spot.

self...right part thank you

ILove your service. The part came in 3 days. Best parts service I have ever found. I was told by the dealer it would take 2 weeks to come in.