7MBPL9764MQ1 Whirlpool Washer - Instructions

Unplug washer. turn hot and cold water off. disconnect and mark water hoses. put a blanket on floor and lean washer on its back. use screw driver to remove metal clamps from water pump. use ratchet or nut driver to,,remove screws from metal clamps on motor.remove metal clamps with screw driver. unplug wire harness from motor. remove motor and remove old drive coupling and repelace with new part.

Removed the the drain hose from the pump. Removed nut from the agitator. Then laid the washer on its back after removing the inlet hoses. took out the pump, remove wire harness from motor then removed the motor. removed the three bolts holding in the the transmission. The one mistake I made was that I removed the springs for the brake shoes and this cause me to have a lot of trouble trying to put them back on. Once the clutch arrived, I removed the old clutch from the transmission shaft, and installed the new clutch using all the parts that came with it. Then put everything together in the reverse order that they were removed in.

unplug electric cord. shut off then disconnect hot and cold water hoses from nozzles. place drain & water hoses over washer. place washer on floor( back/hose side down). use pliers to remove hose clamps(2) from pump. unfasten metal clamps(2) from pump. remove & replace unit. reinstall by reversing process.

Followed the video and everything went exactly as the video said! Just follow the video to a tee!

... exactly as shown in the video in addition to shutting water, removing hot & cold lines & waste tube. I was amazed at how fast the parts were delivered in two days regular shipping. Machine now purring a wifey happy once again! Thanks for the great service & video! I recommend PartSelect highly! WSD

Watched the video, it was so easy, if I had been a little younger it would have been a 15 min job...

Followed the instructions given in the video. Exactly as per video instructions.WATCH THE INSTRUCTIONAL VIDEOS!!

Installed new clutch assembly and while I was at it replaced the Motor Coupling. Actually, I had a good time doing the repair. I am almost 80 years old, so had to have help laying the washer on backside. Got a small stool from which to work (back problems). The only thing I found the least bit difficult was reinstalling the retaining clip for the clutch assembly. The rest was a piece of cake. Were I to do the same repair now, it would take less than 30 minutes. Washer works like new now. Very proud of what I was able to accomplish. Of course, need to watch the repair video so you will know where to start.

After finding out the tub would not spin, I removed the washer to find broken pieces on the floor. I did a google search on my model number and found that the problem was the direct drive motor coupling (it matched the pieces on the floor). So, I watched the "how to" video and I followed the steps verbatim. I found the coupler missing and the plastic pieces on the drive broken. My order came in quickly (within 48 hours) and my washer was running in 20 minutes after receiving the package. It has been great ever since.

Unplugged the washer. Removed the 2 screws on back of control panel. Pulled the control panel forward. Flipped the control panel back. Disconnected the cable from the lid switch. Removed the ground screw with a nut driver. Opened the washer lid. Removed the lid switch. Snapped the new lid switch into place. Closed the lid. Installed the ground screw. Installed the lid switch cable. Put the control panel back in place and pushed back. Installed the 2 rear screws into the control panel. Plugged the washer in.

I unplugged washer, then, removed the control panel with two screws on back, slid unit back and up. Unscrewed ground screw and unplugged harness, lifted lid and removed switch. In order to re-install lid switch, lid has to be in the up position, otherwise it will not fit properly. Reattach harness and ground screw, then control panel. Plug and go. My wife says that the washer works better than ever. Very easy! Saves money!