7DU1100XTSS0 Whirlpool Dishwasher - Instructions

First pulled the end cap off of the slide rail, then attached the rack mount to the correct place on the rack. This was determined by mirroring the mount on the opposite side of the rack. Next, I simply slide the wheel into the open rail and reattached the end cap. Repair completed.

1.] I ordered the wrong part and I altered the contacts to make it work, it did'nt. 2.] Found out the right part # and could'nt hook it up cause I cut off the connection to adapt the first part. 3.] So I had to order an entire wire harness to get a small selenoid connecter. I made the connection and it still did'nt work. 4.] Ordered a control panel and when it came it was the wrong one. 5.] The company sent a new right control panel and BINGO! 6.] Say good night Gracie.

it was easy I saved alot of $$$$$.

Found problem when rack fell into dishwasher. Check for parts availability on Internet and chose partselect.com. I have used them before to order a locking tab for the silverware holder. I Placed order for current problem in late afternoon and parts were in hand within 48 hours. Video instructions made repair EASY for me. I couldn't ask for better service. As my appliances age I am sure I will be using partselect.com again.

I watched the video on your website, and I followed it to the letter. I find the service provided by this company extremely valuable to a person that is capable of doing his own repairs. Thank you, JAK.

The part was correct and I no problems installing it. Just make sure you tighten the brass elbow tight.

I read information on this website about the function of the high limit thermostat. I found that it was the problem by disconnecting the two wires on the thermostat and straight wiring to bypass it. This allowed the machine to work properly so I ordered the high limit thermostat. To replace the part I used a screwdriver to remove the instrument panel and replaced the high limit thermostat by disconnecting the two wires from the old thermostat and connecting the wires to the new thermostat. I then replaced the instrument panel. My machine is working properly again..

First I shut off the power and the water then I disconnected the drain hose. Then I removed the dishwasher from under the counter and turned it up side down. I remover the pump retaining screw turned the pump, removed it. installed the new pump reinstalled the retaining screw. and reinstalled the dishwasher under the counter. I reconnected the drain and water then turned on the power. the dishwasher is working great. Thanks PartSelect for the fast delivery and the right part.

Removed front cover, (8 screws) Removed 4 screws that hold the dispenser in place. Removed and replaced the dispenser, installed front cover and screws. Checked for leaks.

The dishwasher was so load I was sure the pump had a bad bearing. . . After reading the on line comments I examined the chopper and it looked ok. As it turned out the damage was on the shaft and caused the shaft to lock onto the screen without the ability for the spring to work it must have caused excess pressure making the loud noise. I replaced the chopper and now the dishwasher is very quiet again. To replace I took out the baskets and four screw on the big screen and one more screw on the chopper cover then I had to pull on the chopper with moderate force and install the new one . Then I put back the covers and basket. . . Very easy

Took lower impeller off and cleaned. Replaced the little plastic piece and voile - good as new! Was ready to buy a new dishwasher but thought we would try this first. Working as good as new. What a savings eh? Thank you part select for your great service!

The part was easy to install. But , you might have to unhook electrical, water, and drain. That is the time problem, part install is easy. All I had was a socket set, 1/4, drive fits. But a nutdriver would have been easier. WATCH the install video, great info!!!!!

We had to pull the dishwasher out the get the heating element brackets loose underneath. We had to put the new heating element in and then we had to figure out which code to program in to make it reset. the last one listed on the installation instructions was the one that worked. I think it was heated dry, normal, heated dry. It would be very helpful if the reset instructions were put in the manual by whirlpool. I am very pleased with my part that I ordered from PartSelect. It came within 2 days of placing the order.

Remove power to the machine. My particular installation did not require physically removing water and drain lines. Remove the dishwasher from the cavity. Put a towel or two down on the floor. Lay the washer on its face on the towels and this orients the motor in the up position on the bottom of the washer. CAREFULLY unplug the motor wiring harness but if possible, leave the heating element connection in place as spade connectors tend to lose their grip with multiple engagements. Remove the single bolt located between the motor and stainless bottom of the cavity that locks the motor in place. Leave it in the cardboard shield, that really helps in reinstalling it. CCW rotation of the motor disengages it from its housing. Work the motor straight up and out of the housing. This was the most difficult part of the entire process due to the metal housing not quite clearing the plastic pump housing where they mate, but its do-able. Nothing should have to be forced. Now you have the motor in hand. Be very attentive how and what order you disassemble. Remove the back of the motor housing to block the armature to remove the impeller. DO NOT NICK THE FIELD WIRING IN THE MOTOR. I believe the threads were left hand but I don't remember the rotation. They do tighten in the direction of the motor rotation though. Carefully pry the seal out of the pump housing with many short lifts as to not mar the housing itself. Added a little dishwashing detergent on the outside of the new seal and carefully pushed it into place with the end of my screwdriver. Don't cut yourself on the metal insert in the center of the seal.Reassemble the impeller to the shaft WITH the spacer that comes with the new impeller kit. Make sure the impeller is tightened down completely to the end of the threads to insure proper clearances when reassembled. Don't force or over tighten. You'll feel a positive stop. Reassemble the motor to the housing Lubricate the housing o ring seal on the outside with a VERY small amount of dishwashing liquid lest you create a suds factory on startup. Replace the holding bolt on the pump housing. Reconnect the motor leads and heater element if removed. Stand the washer back up. There will probably be water around the door area from the pump when the machine is returned to the upright position. Reconnect lines and check under the pump housing for leaks while in operation being careful not to get into moving parts or electrical connections. Good luck.

The repair went fine just called my grandson in law and he did a good job and he said it was easy.