Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 7DP840SWKX1 > Parts

7DP840SWKX1 Whirlpool Dishwasher - Parts

All parts for the Whirlpool Dishwasher 7DP840SWKX1

Below is a list of all parts for the Whirlpool Dishwasher 7DP840SWKX1. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the 7DP840SWKX1
1-14 of 151
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$6.12

Rack Track Stop

The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes ...

$4.89

Rubber Washer

The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where the heating element is attached. The rubber washer is used to prevent water leaking from your dishwasher during its cycle. Before making any repairs to your dishwasher make sure that you disconnect the power by finding the breaker for the dishwasher, and turning it off. The tools you will need to complete this repair include an adjustable wrench, and a 1/4 inch nut driver. This specific rubber washer is sold individually.

$46.06

Door Gasket - Gray

This gasket wraps around the sides and top of the dishwasher door and helps seal the door when it is closed to prevent water from leaking from the dishwasher during the washing cyc...

$4.48

Rack Assembly Mount with Wheel

Sold Individually. * Part may differ in appearance, but functions same as original. This wheel attaches to the upper rack to glide the rack in and out on the track.

$4.12

Torx Screw

7-18 x 3/4" - sold individually.

$3.02

Spring, Lid

The dishwasher lid spring helps open the dispenser cover in the soap box when the control releases the latch. If your dishwasher does not dispense detergent, is broken and worn out, or the door is not opening properly, replacing the dispenser spring could be the solution. For this replacement you will need needle nose pliers. First, release the cover on the detergent dispenser, then remove the cover from the shaft it hinges on. Pull the shaft from one side and remove the spring from the shaft. Next, replace with the new spring and engage the two open hooks into the soap cover. Finally, grasp the hook and pull it over tab on the side of the wash cup. Verify that it works properly by opening and closing the cap. Refer to the manual provided by the manufacturer for further instructions.

$25.84

Faucet Adapter

The faucet adapter for your portable dishwasher or washing machine attaches to the faucet and allows you to connect the machine to the tap. Before you install the faucet adapter on...

$4.44

Soap Cup Latch Kit

This soap cup latch kit, used in a dishwasher, will keep the dispenser cover closed. If your dishwasher will not dispense detergent, there is a door latch failure, the dishes are not cleaning properly, or there is leaking, then this kit can be the solution to your symptoms. The tools required for this replacement are a #15 torx bits, a small blade screwdriver, and slip joint pliers. First locate the soap box and remove the latch on both sides. Next step is to remove the screws in the inner door panel and remove the plastic cover at the back. Remove the old latch assembly and add the new one. Make sure to unplug your dishwasher before beginning this installation project.

$5.36

Pin (Lid Hinge)

$3.02

Hose Clamp

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on the appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.

$23.76

Door Latch Bolt

This is a door latch bolt for a dishwasher. The door latch bolt fits on the top of the dishwasher door to keep the door closed while the appliance is running. The latch also preven...

$12.93

Soap Dispenser Cover

This part covers your soap dispenser and is spring loaded.

$6.28

Heater Terminal Nut

This nut screws onto the end terminals of the heating element. They are sold individually.

$6.43

Cap, Wet Agent Assembly

This cap does not require the use of an O-ring seal. The wet agent assembly cap is clear in color and made of plastic. This is a part for your dishwasher. This part may need to be replaced if you notice that your dishwasher is not dispensing detergent, cleaning dishes properly, or has sprung a leak. The cap is found on the inside of your dishwasher door. This is an extremely simple repair that requires no tools. Simply open your dishwasher door, twist the old cap out of place, ensuring no pieces are left behind. Screw your new cap into place.

All Parts for the 7DP840SWKX1
1-14 of 151