7DP840DWGX0 Whirlpool Dishwasher - Instructions

Ordered a new Faucet Adapter! Simple

Took inside door panel off. replaced spring that opens soap dispenser lid during cycle. Put inside panel back on. Works fine now.

I Tip The DishWasher On To Its Side So I Could See Under The Dishwasher .I New The Moter Was Working Fine. I Could Here It Runing While It Was Upright . So I Determind That It WAS The Water Inlet Valve . SO I Used A Pair Of Plires To Pull Back The Clamp On The Hot Wate Hose. I Took The Hose Off . And Then I Unscrow the Hose On The Water Inlet Valve That Takes The Water Out Of The Dishwasher.I Then Used A Small Werench To Take Off Two Small Scrows Holding the Water Inlet Valve To The Dishwasher .I Pull Out The Old Water Inlet Valve I Then Found The Modle Number And Seriel Number To My 20 Year Old Whirpool Dishwasher . I Then Went On Line Useing The Name And Numbers Found Partselect And Orderd The Right Part And Put The New Part In .It Took Me Less Than 15 mins And It Saved Me Maybe A Cupple Of Houndred Dallors..Thank You Partselect..

Unplug dishwasher from electrical, water supply and drain hose. Pull dishwasher out from under cabinet. Unscrew water whirler from inside washer, then remove motor. Remove black boot from motor. Unscrew keeper from impellor housing. And you are there! Pull impellor off motor shaft. Replace seal first, then replace impellor. So easy this girl did it. But, this girl also does small engine repair!

I watched the video, which was very good, and did the repair. It took about 10 minutes. Most of that was watching the video. EXCELLENT VIDEO!

I watched the video, read all the post, they all said change the heater. So I did. Only there is a little fuse at the back of the unit that also goes bad and that was my issue. Have it ordered and will be going soon. That said, Part Select made finding and getting my parts a breeze!

Just followed the online instructions. I used white vinegar to clean any residue first. So easy.

Found the adapter on Parts select through a google search. Unscrewed the existing faucet aerator and srewed in the adapter. The plastic shrink wrap holds the washer and screen in place, so don't open it until you're ready to install. Finger snug does it, only use the pliers to remover the old aerator from the faucet. Normally, I don't use pliers, but both of these parts were round and had vertical serrations to engare the plier teeth.

removed the 2 water deflector and slipped the new ones in , in place.. very easy to do but it didn't seem to stop the leak so ordered the door gasket

1. Turn off the electrical switch that powers the dishwasher. 2. Open the door of the dishwasher and find the two phillips head screws that secure the top of the dishwasher to the kitchen counter. 3. Remove the screws. 4. Gently move the machine side-by-side a bit while pulling it out onto the kitchen tile (be careful, the water-supply hose, electric cord, and dishwasher drain hose may not be long enough to allow you to pull it out very far - don't break or kink the hoses). 5. Remove (pull off) the black plastic fastener located on the bottom/rear of each side of the dishwasher. 6. Remove the old surround. 7. Lay the new wrap in place and secure with the two plastic fasteners. 8. Push back into place, secure the two screws, check your hoses.

Remove lower rack in dishwasher, remove dishwasher, lay dishwasher on it's back, remove and replace motor and pump.Install new impellar with new seal. reconnect water, electrical and drain hose. Easy Peasy

I followed the video's from Parts Select and it took me less than 3 minutes to replace these parts. I did find it easier to use a screwdriver to lift the u shape of the spring over the detergent cup as the pliers tended to pull on the spring too much. Couldn't have been easier or faster, awesome!

i took the inside door off and took the 2 switches out and replaced them; not too difficult.

I read everyone else's fixes, which were very helpful but my solution of removing the plastic from the motor shaft was a lot easier than others. I simply used side cutters and made two cuts into that plastic piece and it Fell of. much easier than the person using several Dremmel blades to cut it off.. That was the most difficult phase until I grabbed my ole phone company side cuts and just cut it off in 15 seconds. Thanks for all the other tips. I love dealing with Parts Select, Fast and efficient. Jim W

we followed your instructions submitted via e-mail and they worked out just fine....thank you