79669278000 Kenmore Dryer - Instructions

Replaced thermal fuse

Removed top of dryer
I carefully removed wires from back of control panel
Removed control panel
Most of screws hold cabinet together
Unhook wire from light on door and sensor on the front panel.
Remove the front door and panel together
I changed both front rollers on front panel
If you have to change rear rollers lift tub up by belt
Remove screws on back of dryer that will let you lift out inside rear panel that holds the rear rollers
Change rollers and just revearse procedure to put back together

Following the reference video, step by step and taking progress photos along the way, organizing screws and hardware as they were removed.

The discrepancy I found was the new rollers that I received were complete with the shaft. The video with the older rollers instruct removing the rollers from the shaft.

To use the new rollers with the new shaft, requires removing an additional panel at both the front 2 and also the full back panel for the rear 2, to get a wrench on both ends of the shaft, and then attach the new roller bearing shaft assembly and re-install the panel.

Other than that, it went very smoothly and the result was a quiet rotating drum. No more thumping!

My dryer actually required 2 moisture sensors, but had only ordered one pack, which only came with 1 sensor. For whatever reason, I thought the pack would have had the 2 pieces.

Another reviewer made note to wear work gloves as some of the hardwares metal edges are quite sharp. Following that advice I completed the repair in 3 hours without a scratch. Thanks for the detailed video Partselect team and good luck to all attempting repairs.

order start button and was sent thermal, reordered and rep sent me a button that was not for my machine even though she had model no.,called third time and was told I had to order new control panel but they were not being manufactured any more.so it is not fixed

Watched a You Tube video

One of the roller assembly froze up & had a flat spot on it. There for causing the drum not to rotate. Pulled it out replaced the roller & up & running.

Take old one out and slide new filter in.

I watched video by searching by the part number. It was recommended by Sales Lady(Can't remember her name). I removed door from the unit and then removed all the screws on the door. There was about 16 of them. I then pushed on the 2 plastic clips which raised one side of the door. This exposed where the Door Strike goes into. I removed the screw that holds Door Strike in place. Inserted new Stronger Door Strike and lined up hole with screw slot. Screwed back in till tight, thus locking Door Strike in. Inserted all screws back in, and attached door back to unit. Tested fine and have now done several loads no problems. A $4 part would have cost me hundreds by service company. Thanks Part Select!

Put the new lint filter in and it was completed

Initially replaced igniter. Didn't think it was bad though. Read other suggestions on another website. None were the correct diagnosis for my situation. And when I figured it out they did not offer correct part. The dryer thermistor temp sensor (probe sensor) is what I replaced. Found it on Parts Select. I did replace other parts also. But that's the one that ultimately was the issue.
Was not hard at all if one is even a little handy.

Entered dryer from rear exhaust port. Removed 2 screws and 2 clip on wires. A little awkward of process but superior method over disassembly of drum and main parts.

Replaced idle pulley wheel, worn drum belt and all 4 rollers (1 frozen) due to dryer age. Site video re general disassembly/re-assembly easily adapted to this model and very helpful with exception of replacement of drum rollers. New rollers received (AGM75510755) were pre-mounted on included shafts. This required removal of existing roller shafts to replace with new shaft/roller units. Site video shows placing a new roller on existing shafts after removing a plastic retaining clip. New roller/shaft assembly is a better option and fortunately I did not order extra retainer clips! Rear drum roller shafts have small carved out space to fit a box end wrench to remove shaft nut. Watch out for sharp edges on internal steel parts!

There’s all sorts of videos on it I watched. It was actually very simple

Followed the instruction on video.was great after three parts now is OK .we have heat.still cheaper than having it service.

With a thin flat screwdriver I was able to pry out the old door switch, I replaced it with the new door switch, pushed back in dryer and so far is working since I installed a month ago.