79641728900 Kenmore Washer - Instructions

Totally dis-assembled this washer to check the bearings and drum plus fix the pump problem. We wash dog blankets occasionally and found the little drain hose from the front door gasket was clogged with hair. It makes a 90 degree turn and it gets caught there. THAT fixed the smell issue. As far as the pump replacement goes its quite easy. Videos online are your friend.

Follow the LG washer video.

Used Youtube to look for a set of repair instructions. From start to end 35 min.

The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.

Overall very easy to do.

Line up the plunger with the existing slots in the door and push in.

NOTE: When testing it was evident that the magnet was not as strong as the original one. I would rate as one step up from useless.

ridiculously easy. removed the door gasket ring clamp. separated the gasket from the face. unscrewed the lock, removed the wire(gently). replaced the wire on the new lock. replaced the lock. replaced door gasket and ring clamp. washed clothes. Note- I had called a repair service and was given a $360 estimate in addition to the $130 dollar service charge. All total- $50 dollar part(with shipping), less than 45 min total time and I'm no mechanic!

The video from PartSelect showed removing the retaining ring from the rubber washer tub boot to then allow access the door lock located behind the boot for replacement. That ring can sometimes be a real pain to put back on. This can be avoided altogether!

It's much easier to access the door lock switch by removing the two retaining screws on the top cover of the washer found in the back of the machine. Remove the top cover and you can then reach down to remove the wiring connector, unscrew the two phillips screws on the front of the door latch and remove the door lock. Put the new switch on in reverse order; plug in the connector, replace all screws and the top cover, and you are done! This method took than 10 minutes from start to finish.

Please note that the washer should be unplugged from power while working on any electrical component.

the magnetic door plunger fell on the floor, would not stay in place and did not hold the door closed. Received a new on, put it in place. works just like it is supposed to. took all of 2 seconds. great service from
Partselect. got the new part in less than a week.

Thank you

pops right into hole

Simply inserted new plunger/magnet back into door with thumb&finger until you hear the little locking tabs click. No tools required.

I already had the top of the washer open, from previous disassembly to clean the front loader seal, and when I ran a trial load, noticed a small 1/4" tear in the hose bellows that attaches to the drum.

Very simple repair, remove the existing hose by loosening the clamps, paying attention to their orientation. Install the existing hose clamps onto the new hose, install and tighten the hose clamps.

5 minute job, if the washer top is off (which is also simple).

Super straightforward to diagnose and repair.

There was puddle under the washer.

I removed the top (screws in rear, slide top toward rear slightly and lift) and followed the trail of water up to the top washer hose between the drum and detergent tray.

Two hose clamps to remove and replace, then replace the top and ready to go.

Not too bad, had a neighbor help with the project as washer/dryer were stacked. removed dryer from on top out of way. Drained washer, tilted on side to get access from down below. Second person help here. unscrewed drain pump from front, Used pliers to unclamp hoses, disconnect wires to motor (already pulled power from wall) pushed plastic clip holding in unit and pulled out. New unit was factory new, not a knockoff. We took extra time to clean out hoses, especially from the main washer unit, it was a simple unscrew clamp and pull hose down. We sprayed out gunk from hoses and parts going back in. Once new unit was ready, installed back and reconnected hose and power. The clamps were somewhat of a pain with the overall size and angles to get them seated and on correctly. Much easier to take off, but take the time to reinstall correctly. Don’t need water leaking. Motor much quieter now, wife is happy.

WATCHED VIDEO PROVIDED BY PART SELECT, AND FOLLOWED INSTRUCTIONS. VERY SIMPLE REPAIR.

2 hose clamps and a hose, easy! This would be a very common cause of leaks in washers due to all the movement inside.

Remove where the water pumps are and remove the one that was damaged easily