Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Temperature in the oven was not consistent
1. Turn off power to the electric oven 2. Removed the two screws in the top side of the oven that hold it into the cabinet. 3. Made a support to set the oven on once you remove it from the wall. Or set it on the floor. You will need help this is not a one person job. 4. Used a Philips head screw drive removed the back of the oven panel. I did not have to remove the whole thing just took out half the screws and the electrical plug for the temperature sensor is right on the edge. 5. Unplugged sensor 6. Took out the two screw on the inside of the oven that holds the thermal sensor in place. Pulled it out the front. 7. Side the new thermal sensor in place replace the screws. 8. Pull the plug out and plug it back in. Check and push the insulation back in place where the thermal sensor. 9. Replace the back and replace the screws. 10. Slide oven back into the wall. 11. Replace the two screws that hold the oven in place in the frame. 12. Turn power back on Check the temperature
I usually try the cheapest part to replace when I come to a fork In the road but I wasn't home at the time and my other half called in the "expert". He said it was the clock timer and it would be $450 to replace it. She sent him away and I bought one online for $200 and put it in only to find out that it didn't solve the problem. Did some reading and found out that it could be the sensor. Put an ohm meter on it and found that to be the problem. Left the new clock timer in it anyway so now we're good for another 100,000 cookies or 1000 pizzas, which ever comes first
Front left burner would not shut off, then switch fried
Unplug range, remove top back panel. Remove knob. Replacement part is different, but if you look closely, each metal tab has a number stamped on the plastic housing directly beneth it. Remove old switch (2 screws)and remove and replace wires one at a time. You will need to cut the "one size fits all" metal shaft that the knob attaches to. We had to remove most of it, leaving only 2 "segments". File rough edges and apply vaseline so that the plastic sleeve will slip right on. We used the shorter sleeve (only 2 that are supplied will fit the knob). Replace unit and screw in. Replace knob.
Switches were going bad and making a popping sound and smoking.
Pulled out the range, unplugged it and removed the upper back panel. The switches were held in place with two screws. Removed the old switches, detached the wires and plugged them into the new switches. Mounted the new switches, replaced the back panel, plugged the range back in and pushed it back into position. Appliance repair company wanted $370. I did it in 45 min. for less than $100.
I was required to remove the control panel to access the plug as it had been broken and the switch had been shoved into the unit . It would have been extremely simple if the plug had remained on the outside surface My son can now clean his dirty oven
First you must disconnect power by throwing the circuit breaker off.You need to pull knobs from cook top. check underside to see if it is mounted to counter top, mine was not. Then raise the cook top and support bottom with 2x2's. Mine had three main screws in front, one on the sides and two in the back. The other thing you need to do is loosen the metal plates that have two screws on each plate. Three plates in front, two on each side and three in back. Once these are loosen, you can lift the stove top up to reveal the indicator lights. I found it was easier to support the top with a pan or something while working on it. Replace your indicator light and put everything back together.. It really wasn't to bad.
Phillips screwdriver used to remove 2 screws at top left in oven. Pulled thermostat out until I could get to the connector. Used pliers to hold wire, reconnected new plug , threaded it back into back of oven and reattached the two screws. Saved $150 on a service repair call.
Oven would start to heat then quit,checked the temperature sensor with ohm meter after cool down reading about 1100 ohms. I cleaned connection tried it again seemed to work well but quit again in just few days.
Pulled range out from cabinet, removed back plate, two screws inside oven attaching the temp sensor. Then pulled the sensor and wire through from back. Reverse to replace about Ten minutes OEM parts plug in same, works great
unscrew the sensor inside the oven; took off the back of range to access harness of sensor; the replacement part harness did not match up to the original, so we stripped the clip from the end of the part and also the end of the harness in should clip into. after joining the wires together with ceramic wire nuts we tested the oven to make sure all worked AND IT DID!