79094001400 Kenmore Range - Instructions

unscrewed two screws, exposed wire connections. Disconnected two wires, then placed new element in oven and reconnected two wires, then pushed connectors back inside stove body. A acordless screwdriver made quick work of the two screws and the element works fine. Thank you for your quick delivery.

Lift stove top cover up and support cover so it will not fall down unplug element put new one in close cover and turn burning on and watch the burner get red hot. simple job why call a repair man in. Vicki

Watched the online video and followed the instructions. I unplugged the oven, used the nut driver to loosen the screws, removed the old element, hooked up the new element and voila... back in business. I received the part the next day after ordering it!

I watched you vedio and done just as the vedio told me how to change the switch. When I got the switch on pluged it in turned it on and every thing work great. thank you very much.

Turned off electric to range, removed old element, replaced it with the new one, then turned electric back on. Super easy.

This is a slide in oven fully contained not in a wall, or wood enclosure. I slid the unit out away from the wall unplugged the power cord, used the nut driver to remove a dozen screws, not all of them, you dont need to pull the top back plate off just unscrew the bottom 3-4 screws on the top plate to release the lower back cover plate and you see the probe wire and the insertion point/hole. I actually did not even need to pull the full back plate off but it makes the handling of all the tools and stripping easier. I wish they had just left the plug off of the new probe and had left the 2 loose ends of the 2 wires that had to be spliced, it would have saved 15 minutes just with that part. If you dont have a real splicer tool ya gotta be careful to not cut the wires themselves if you use a sharp knife. Just cut the new probe plug off and splice on the old plug from the bad sensor which obviously you have cut and strip as well as I did and then it fits nicely back together like it was ment to be. I put elect tape on the 2 splices, you could use small wire nuts or whatever you desire, but turn the exposed splices back away from each other and tape them to the insulated wire so no exposed wire is touching any metal then I wrapped the completed taped splices with about a 4x5 piece of aluminum foil to help deflect the residual heat coming from the oven when it is on. put the probe through the hole and placed the metal retainer back in place and re- mounted the back panel plate,cover, that was it problem solved. This entire problem was caused originally in this relatively new oven because people who have been using the oven were sitting heavy pots and pans on the oven door and the hinges were sprung. The door would not stay shut during cooking. I dont know how long this had been going on before I discovered the issue. Once I replaced the hinges ( parts select ) the uneven, wrong temp, extended cooking problem jumped up. I am certain it was related to the open door not shutting for several months. They were using a bungie cord to pull the door closed and not completely. At this point I feel very comfortable with using parts select for all my appliance parts and advice. The folks here at my facility think I am an Einstien but when you have parts select working with you in the background you can't go wrong. I asked a hundred questions and learned alot and saved the facility at least 400 dollars by doing it myself. Thanks to my new work buddy PARTS SELECT. I was really a bit apprehensive about the doors hinges they looked dangerous and might have been but the tech I spoke with at P.S. walked me through it on the phone and I read the blogs which are really helpfull SORRY THIS ONE IS SO LONG.

First the item we ordered arrived in 1 day, we were totally amazed!! My husband switch out the heating element and it worked!!!! Thank you for great service!!!!

I had the old one out and new installed in less than 15 minutes and I would like to thank you for the promptness of your delivery

We turned off the power then unscrewed the element . After removing the element from the connectors we taped the wires to the oven so as not to lose them back into the holes. We attached the new element, pushed the ends into the holes and refastened the nuts. Very easy and now we are back in business.

I watched the video on your web site, and it couldn't have been any easier. This is the second major appliance that I've repaired using this web site, and your instructions have been perfect each time, as well as parts cost. I can't get parts at any lower cost including shipping! Excellent resourse here!!!

repaired in 5 minutes with my nut driver. So, so, so easy to make this repair. And never even attempted to call an electrician. Since long before I became an official widow, I say...who needs a man...

Unscrewed the two screws which held element in place...pulled straight out...gently pulled connector terminals off....replaced with new element connecting element terminals ...sliding element back into place (make sure terminal connection is straight (ie NOT BENT) when pushing element back into original position)and screwing screws back in...DONE!!! EASY PEASY!!!

removed the screw at the mount on each side of element .pulled old element straight out untill wire connector was out at the back of oven ..unplugged wire connector from each end of old element ..plugged wire connectors back into new element .pushed element plugs back into back of oven and installed each screw that holds element into place.. real simple

The video was a great help. I could have replaced the switch without watching it, but it gave me confidence that I was doing it right. Everything went just like he said it would. Burner seems to work better now and no more scary noises.

aftering watching your repair video the repair went very well we took the oven door off to make access easier. the worst part of the repair was getting the door back on.