Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Long time to light, strong gas smell
Unplug power, remove draw, marked and cut wires, unscrewed and removed old igniter, replaced and screwed new igniter into position, reconnected wires with supplied porcelin wire nuts, replace draw, plug in and tried...working great.
Oven progessively taking longer and longer to preheat
Disconnect appliance from electricity source! Removed oven grates and the solid oven floor by removing the two screws and lifting up. Removed the piece of metal covering the oven igniter. Unscrewed oven igniter, snipped the wires close to the old igniter (read some of the better descriptions on how to do this). Reconnected new wires to the existing ones and used the ceramic wire covers that came with the new igniter and pushed the wires back through the opening in the rear of the oven. Screwed the new igniter in place. We actually had to unscrew the little metal box on the back of the oven to get to the wires which was easier to work there with connecting the wires. It was a little difficult reaching into the stove since we didn't remove the oven door.
The stove was older so the burner was hard to get out. The small screw heads broke off, so I had to carefully center punch and drill out the screw bodies. The igniter screw was also frozen in the pot metal burner. That screw requied drilling and tapping with the installation of a new 6-32 screw. Once the burner was refurbished, the igniter mounted easily. Afte attaching the gas line and igniter wire, the burner worked great.
Our original oven ignitor went bad. The gas supply won't even open, unless the oven senses the proper voltage / resistance across the ignitor, so that gas won't be flowing without ignition.
PartSelect was very good about providing me with the proper part, after I got the part number from their schematics and wiring diagrams, on the website. The first replacement part actually arrived, broken, from shipping, but when I called them, they immediately reprocessed the order, and sent me a new ignitor, to arrive the following day. I was very satisfied with their professionalism, as I've been in the past with them, as well.
On to the actual repair:
I removed the broiler drawer from the drawer slides, reached under the main oven chamber, unscrewed the two screws holding the ignitor in place, and cut / disconnected the two wires supplying the power to it.
I then put the new ignitor in place and screwed it back to the mount, used the wire nuts that came with the new ignitor to reconnect / splice the wires, and put the broiler drawer back in place.
Oven fired right up!
Entire process took less than 35 minutes. (Likely would've taken a bit longer, but this is the second replacement for the ignitor, since we've owned this oven, so I already had a good idea how to do it. (The first replacement for this particular part was NOT from PartSelect, so we're hopeful this one lasts a while longer than the previous one.)
I removed the back panel, about 6 screws, then found the probe which was attached by 2 screws. Unscrewed them and unplugged it. Plugged the new one in and replaced all the screws. The oven works like a charm now! No more F3 errors!
I searched the item I needed and followed a link to PartSelect.com. I paid a little extra for shipping and literally recieved the part in two days. The part was an absolute perfect fit and my wife and myself have never been happier. Home cooked meals again thanks to the folks at PartSelect.com. It couldn't have been an easier.
Make sure you unplug the oven before you begin. I removed the old igniter. The top wire on the igniter goes to the back of the oven and plugs into a flat blade type connector. Instead of using the twist wire nut I used a flat connector because it was easier to put on and is foolproof. Make sure you cut the plastic insulation off the connector so it does not melt when the oven is in use. I used a wire nut on the other wire and that was it. Very simple and the oven works great again.
The temperature was irratic the entire time the stove was on. I would set it for 350 and it would go up to 425 then down to 275. It was all over the place.
It was great. We ordered the part, it was shipped the next day and I had it the day after that. It was easy to install and the stove has worked perfect since. Color us happy!
removed shelves and base, removed 2 screws that held igniter on, disconnected wires from gas valve removed protective cover in corner {1 screw} disconnected plug, removed igniter. This igniter was easier to remove from front of stove on this model
The oven would take forever to heat up, and sometimes not at all. Othertimes it would heat up, but not stay hot for the entire baking time.
First, I unplugged the oven from the wall. I opened the bottom drawer of the oven to see where the igniter was mounted, which was directly under the bottom pan of the oven itself. I opened the main oven door and unscrewed the 2 screws that were holding the pan to the bottom of the oven. Then, I slid the pan back towards the the back of the oven and it popped right out.
There were 2 hex screws that were holding the old igniter on, so I unscrewed them with my socket set. I made sure to pay attention to which wire was the top one and which one was the bottom one coming out the back of the igniter. I pulled off the wire nuts connecting the igniter wires to the wires of the oven. I striped the wires on the new igniter and re-attached them to the proper wires of the oven, using the included replacement ceramic wire nuts. I re-screwed the hex nuts in, mounting the new igniter to its proper place. I put the pan back and screwed the 2 screws back in to hold it in place.
Plugged it back in, turned it on, fired up within 20 seconds. Good as new.