Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven would not get up or stay up to selected temperature
Pull stove out to get behind it,unplug temperature probe plug. Remove temp probe from oven by removing the screw holding it in place on back of oven. Cut plug off temp probe unit leaving as much lead wire as possible on plug end. Strip wires on new probe and end of plug wires(one quarter inch). Then I used two small butt connectors to join the stripped wires,one for each pair of wires. Two small wire 'nuts' may also be used as the connections are outside the oven and not exposed to the heat of the oven while it is in operation. Hope this helps the inexperienced 'do it yourselfers'--:)
Took 6 screws out holding the top on from the sides. Lifted the top front, popped out the spark module, Took 6wires off & reversed the processed to install the new one. I was really amazed when I ordered it Wednesday and it arrived on Friday. Believe me I bookmarked this site.
Very simple with instructions supplied, Removed two screws inside on back of door, then removed four more screws to get to inner glass,removed broken glass installed new glass, replaced all screws.Job completed. very good instructions,Thank You.
Actually, the igniter I purchased is to be used on my furnace.
I have a Nordine model G2RC-105C19 LPG gas furnace. It was installed in 1995. The igniter went out and my son who was a propane gas appliance service tech installed one that was for our gas range. He said they were the same with the exception of a metal mounting plate on the stove igniter. Once the plate was removed, the igniter fit perfectly on the furnace. As a side note, the one I just bought from PartSelect was less expensive than one for the furnace.
PartsSelect.com saved me lots of $$$$$. I have had appliance repairers come and view the stove and tell me I needed so much work. I paid them and the stove still wasn't fixed. I figured out the problem and found PartsSelect.com = savior!
removed gas safty and igniter .replaced 4 screws and 3/8 wrench. make sure you turn the gas off frist.after repairs are done make sure there are no leaks at fittings.
replaced temp probe per your suggestion. No improvement! checked both heating elements with ohm meter. OK Next suggestion was replace circuit boards. Bought new range for less than cost of 2 oven/range control boards.
Pulled stove away from the wall and unplugged it. Removed probe and cut the wires because the connection clip on the new probe was different from the original. Leave the wires as long as possible because you will need the extra length to splice the clip from the old probe to the wires on the new one. Replaced probe and plugged the oven back in. Done.
Removed the door and carefully dismantled all of the layers. In my particular situation, I needed to do some high heat painting as over the years the white panels had discolored due to heat. So, I had to wait a day or so for the painted panels to dry--but they looked great when done. Some words of caution, really look the diagrams over and be sure you are ordering the correct glass (there are three and all different). I initially ordered the wrong one but used it anyway as it replaced a badly stained one. But, I had to re-order the correct glass. It was amazing how quickly I got both orders, though. Only took a couple of days!! So, am very pleased with the way it looks--like new again and quite easy if done systematically!
Unplug the stove from the wall socket. Remove the oven door as shown in the instructions for replacing the door. This makes the job a lot easier. At the rear of the bottom panel there is a screw at each corner. Remove these screws, a screwdriver will loosen them, then remove by hand. If you have a convection oven remove the fan cover as this prevents the bottom panel from coming out. There is a screw at the top and the bottom of the cover. You can then gently lift the bottom panel at the rear and work it out of the front lip. Install the new bottom panel in reverse order.
First I watched video on how to repair oven door glass. The important part was how to remove oven door! If I would have watched the video before trying to clean the inner glass, I would not had to do the repair in the first place! After that everything went fast and smooth! I was very impressed on how fast I received the replacement glass from Part Select.... less then 24 hours! Thanks again for the quick service!
Bought a electric range/oven with a broken glass in the door cheaply because the owner didn't think they could fix the glass. I watched the video on You Tube on how to handle the spring loaded hinges and followed the steps as presented. The toughest part of the job was cleaning all the crud on all of the glass due to the gap in the inner glass. I had to use a square drive and a phillips head screwdriver to disassemble and reassemble the door. It took less than 30 minutes to complete the job and most of that time was cleaning the glass.
