Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Bake element burned out in my slide in range
Turn off circuit breaker Open oven remove two oven racks Position flash light Remove two Phillips head screws that hold the element in place Gently slide out element until you locate the two small wires Gently Detach the two small wires from the back of the burned out element Position the new element in the bottom of the oven and attach the two small wires to the back of the new element Gently slide the element back in place and replace the two Phillips screws that hold the element in place Make certain the new element is lying flat on the bottom of the oven Replace the two oven racks Turn on the circuit breakers and test the oven
Remove the lower bake element by removing the 2 retaining screws that secure the element to the inside oven back. Carefully slide the element out. There are 2 wires attached to the terminals of the element. While removing be careful to not pull the insulation out with the wiring. Attach the wires to the terminals of the new element and reinstall in reverse order.
I shut POWER OFF FIRST and tested it be fore I started. I left all but one wire intact on the old switch and when the new one arrived I made sure it was the right one(it was) and then I just removed one wire at a time from old switch to the new one. After the install was complete turned power back on tested it and it worked. Good luck!
Turned off electricity to the stove top opened up the aluminum cover under the stove top with the screwdriver Took off the wires one at a time with the pliers as they were on tight and replaced them on the new part Replaced the aluminum cover Turned on electricity and voila it worked fine no sparking
1. Loosened 2 sensor mounting screws and removed them. 2. Tripped range circuit breaker to off. 3. Pulled out the range but left gas connected. 4. Loosened the 4 screws on RH side of the top back panel and carefully pried that side of the panel open. 5. Using fingers, threaded the sensor's wiring harness through insulation and into the oven. 6. Unplugged old probe. 7. plugged in new probe. 8. tugged wiring harness back through insulation behind the oven. 9. Using 2 screws removed in 1 above, mounted new sensor. 10. Repositioned top back panel and fastened it in place. 11. Shoved range back in. 12. Tripped range circuit breaker to on. 13. Reset clock. 14. Set oven to 450 for test tun. 15.
The original element in the oven burned up one evening
We pulled the stove out from its slot in our island. We unplugged it and unhooked the gas line so we could get behind it easily. We then took off the back (using screwdriver) to get to the connectors for the element. We unhooked the connectors from the old element. Then we took off the plate inside the back of the oven (using screwdriver)and gently pulled the old element out. We seated the new element in the oven and then hooked it up in the back and put it all back together again. It worked perfectly! The hardest part was cleaning the dirty floor under where the oven had been for 7 years!
Bottom oven quit heating about 6 mos. ago and now top oven quit. Broiler worked fine on both. Bought 1 replacement element to try. Did not work on either oven. Found online where someone had found a bad solder joint on a relay board so I pulled the oven and removed the covers. (WITH POWER OFF. I made a diagram of the wire connections to the board and removed it. I FOUND a cold solder joint on the L2 connection of the top oven board. I found the exact same cold solder joint on the bottom oven board also. After resoldering the connections and touching up any suspect joints I replaced the boards. They BOTH WORKED fine! Anyone that can't solder can take the boards to a local radio/TV repair shop and probably get the techincian to resolder it for a minimum fee. It is certainly worth the attempt.
It's kind of embarrassing! As the breaker was being thrown to turn the current off, I discovered that the breaker box was burn up at the breakers. Short story but I got'er done! The problem now is there is something still wrong with teh oven! I think I see a new one in the future! Thank you very much for the very prompt delivery. My purchase has been without a flaw. I have already sent the part back for a refund. It cost me something like $13 for this experience for freight. I will remember you with my next need.
A friend shot out the front glass panel of my oven door with a BB gun!!
Just "locked" the hinges, pulled the door off. Removed the broken glass for the door. Switched the handle from the old door to the new one. thPut it back on e hinges.....viola!! new oven door glass!