Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 6AMTW5405TQ0 Maytag > Parts

6AMTW5405TQ0 Maytag Washer - Parts

All parts for the Maytag Washer 6AMTW5405TQ0

Below is a list of all parts for the Maytag Washer 6AMTW5405TQ0 - Residential. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the 6AMTW5405TQ0
1-14 of 183
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.92

Suspension Spring

The suspension is meant to support the outer tub and keeps the tub steady during loads that could cause an unbalance. If this part breaks, is worn down, or perhaps has stretched ou...

$46.97

Clutch Assembly

A clutch assembly is found in your washing machine and is responsible for spinning the basket during the spin cycle. A worn-down clutch can lead to a slower spin which can lead to the machine not draining properly, leaving your clothes wet after a cycle. If you notice a burning smell, or the machine shaking and moving more than normal, this could indicate the need to replace your clutch. This clutch assembly comes with a brake cam driver, blue springs for large capacity washers, and a black spring for compact washers. As per the factory, the green spring (1.24 inches) replaces the black spring (1.46 inches). This repair requires a half inch 1/16th socket with an extension and a ratchet, a pair of channel lock pliers, a Phillips screwdriver, medium size flat blade, a small flat blade, and a 1/4 inch nut driver.

$23.02

Switch, Lid

This part is found in your washer. The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed. This part includes the green grounding wire....

$3.56

Tub Spring

This tub spring is also known as suspension spring, balance spring, or counterweight spring. It is sold individually. The function of the part is to counterbalance the weight of the motor on the front of the front-load washer so the washer tub sits straight and even during the spin cycle. You may need to replace the spring if tub is sitting tilted forward. A broken spring will result in the tub being off-balance during the spin cycle which can cause further damage to washer parts. It is recommended to check all suspension springs as they often wear at the same rate. Tools needed for repair are a Phillips screw driver, flat blade screw driver, and a pair of pliers.

$4.63

Screw & Washer (5/16-24 x 1)

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

$12.16

Tub Wear Pads - Package of 3

This package of pads contains three brown tub wear pads.

$6.88

Leveling Spring

This spring is used on the leveling components in a washer. Please note, this spring may differ in appearance, but functions the same as original.

$4.36

GASKET

This part may also be referred to as a main outer tub seal. This part prevents leaking from the bottom of the tub. The gasket is approximately 2 inches in diameter to the outer edge, black in color, and made of plastic material. To perform this repair, you will need to disconnect the power, drain hose, and the inlet hose. You will need to remove the entire outside cabinet to have access to the tub assembly. The tub will need to be removed entirely. This is a genuine part that is sourced directly from the manufacturer.

$2.81

Foot, Front - Single

The front facing foot is sold individually. It is used on your washing machine and can also be known as an adjustable leveling leg. This specific front facing leveling leg has a ru...

$16.42

Suspension Pads - Package of 3

$25.98

Drain Hose

This drain hose is 42" long and includes the clamps.

$3.02

Hose Clamp

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on the appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.

$3.02

Cover Screw

Sold individually.

$4.37

Retainer, Suspension Spring

All Parts for the 6AMTW5405TQ0
1-14 of 183