687WF-CKVW Admiral Range - Instructions

Remove the the drawer of the gas range on the bottom, on the right side there is a alluminum cover with a bunch wires, held on with two screws,inside is the igniter kit module, make sure you unplug the range from the wall . unplug the wires from the unit and plug the new unit up and you are finish.Good luck.

First, I removed the racks, door, bottom drawer, and lifted the bottom pan up and out from the rear. Then, I unscrewed the bottom cover for the electrical stuff (under where the drawer is) as this is where the connector for the igniter is. I did a voltage test on the oven side of the connector, finding voltage there I removed the igniter by removing the 2 screws holding it to the burner. (pack lunch for that part, they will be rusted, I used a mini grinder to cut off the heads). Then I pulled the connector through the hole, and installed new igniter using self drilling screws. After i repacked the insulation, I put it back together, and it lit right up. The failed one had a bad ballast, confirmed by a continuity test.

Pulled out the plug, pulled out the stove, removed the oven door, pulled out the lower shelf and racks. Used a nutdriver to remove the 2 screws from the bracket, disconnected the old ignitor, new ignitor was an exact replacement, put back in the screws, pushed back the stove and plugged it back in....Was back in business in a matter of seconds!!

Broiler lighting fine but main oven burner not lighting. I deduced the oven igniter was most likely the point of failure. Decided to replace empirically rather than time and money for service call. Process was about as easy as replace a computer part. Removed pan and flameguard. Unplugged part from below (after removing drawer). Such a simple plug I didn't bother to throw the breaker / power down the oven. Pulling it out to get to wall plug not an option. Unscrewed old part, saw a flaw had developed in the element. Screwed on the new part, plugged it in, inserted insulation in the hole. Tested for lighting - lit first time. Replaced guard and pan, oven has worked reliably since. Research time was 5x the repair time, but in all a fraction of time and money to have a "pro."

Remove lower pan. This is tricky -- pull clips at the back of the pan forward (they may stick), Then push pan to back and lift forward portion up, exposing igniter and gas tube. Use nut driver or socket set to unscrew the two mounting screws. Had to use pliers at one point to pull on screws while turning as they were cross-threaded, perhaps due to heat. Cut wires to igniter. Pull out oven and look at exterior back of stove -- at bottom near the center opening. The power feeder wires to the igniter are red and terminate in a jack -- disconnect the igniter plug connector and pull the cut wire through. Back to the inside of the stove: you now have to force the connector for the new igniter through the insulation at the back. Pull some of the old insulation out to make this possible -- new insulation is provided in the kit. Then at back of stove connect new igniter plug to power feed jack. Then screw in new igniter with the original screws. I had to use pliers again while turning to force them past the cross-threaded area. Replace bottom pan and you are in business, saving a lot of money!!

Figured it had to be the ignitor. I didn't use a multi-meter. Since the appliance was so old, if the $50 igniter didn't do the trick, I'd just replace the oven. Install was super easy, and now oven works great!!!

Removed door. Removed bottom linerin stove that cover burner. Unplugged old ingnitor. unscrewed old ignitor. Removed old ignitor. Screwed in new ignitor. Plugged in new ignitor. Checked function. Put door back on and bottom liner back in. Took less than 15 minutes. One of the easiest repairs ever.

1. Pulled the bottom plate out of of the oven (plate separating oven and broiler). 2.Remove the gas tube. 3.Remove back plate found at the bottom of the inside of the oven (4 screws). 4. Remove igniter from bracket and disconnect wires. 5. Connect wires from new igniter to oven (2 wires). 6. Connect new ignighter back to bracket and 7. re-assemble steps 3,2,1. Easy

Fist I removed the screws on the front-sides of the oven. Then I turned off the gas, by adjusting the in-line valve. I then unscrewed the gas fitting going into the bottom of the oven. I pulled the oven out, being careful not to put too much pull on the electrical cord. I put a bench in front of the oven and set it down.
I then removed the oven racks, and the plate in the bottom. Bottom element is bake, top element is broil. I unscrewed the igniter, then disconnected its plastic wire connector on the back of the oven, then pushed and pulled the connector into the oven and out the door.
Then I ordered my part for $30 less than Sears from PartSelect, and it got here STUPID FAST. I hooked it up and put everything back together, no big deal, BOOM - Cornbread!

I removed the oven door and floor, removed the two screws holding the old part in place, unplugged it from the wiring harness and plugged in the new part and replaced the screws. Fixed in 5 minutes.

I was worried over the fact that my oven was filling up with propane but taking a long time to light. One day it didn't light for over ten minutes. I shut it off and put the still frozen pizza back in the freezer. That's it, I thought. I'm not going to use the oven again until it's fixed.

I looked online and ordered the part. It came within two days time,even though it was a weekend during the holiday season. My husband spent about 15 minutes with his head in the oven and then said it was fixed.

I baked several batches of Christmas cookies and three coffee cakes the next day.

I was afraid I would have to remove the built in oven from the wall to do the repair but it was simple. I pulled on the wire a bit and the connector popped out of the hole in the back. After that it was as simple as removing 2 screws, replacing the unit, plugging it in and pushing the new connection out the hole in the back. They included a piece of insulation with the kit that I then forced into the hole to protect the new plug from the heat of the oven.

Much easier than I thought it was going to be. In about 10 minutes I had the oven working again.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I
attached the new element with the two new screws and connected the two wires and then I turned the oven on and had heat immediately. It's real simple to do..this makes the third time that I have installed this particular part but my Magic Chef wall oven will soon be 20 yrs old. Thank you for making do-it-yourself so easy!!!

Removed the two screws that support the hot surface igniter. Removed the rear cover to disconnect the igniters wire harness and removed old igniter. Installed replacement igniter by fastening with the old screws and sending the plug harness through the ovens rear opening. Connected igniter into the harness and installed the rear cover.

Well, this wasn't my first rodeo, this is the second ignitor I have replaced in my oven, first being the broiler. It is very simple, unscrew the old one, screw in the new one. The hardest part was cleaning up the mess I found UNDER THE OVEN!!!!