Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
dishwasher leaks from left side of door
The old gasket came out easily, but had calcium deposits in area. I cleaned the area with vinegar and water and waited until it was completely dry. The new gasket went in very easily and looked great. I started the dishwasher and alas, it still leaks, so the problem was apparently not with the gasket, but some other area. But the gasket is nice and new. Any suggestions on next step0 in troubleshooting?
first i picked out the old seal, use a screwdriver to get it started. Then I pushed the new one in after cleaning the seal channel. I fixed it during a commercial while watching my favorite tv show.
i took off the kick plate and found the water valve. its the piece that water comes to from under the sink to connect to the dishwaser. it has a plug with 2 wires. i turned off the water supply, disconnected the wires(probably should have flipped the breaker but didnt) took out the 5/16 mounting screws, had to use a little end wrench on 1 because it was behind the water line and a nut driver on the other. i put some thread gook on the connection and put the new one in the way it was and it works great. i am writing this because thats where i got the info to diagnose in the first place and saved me $$$!
My dishwasher's heated dry cycle wasn't heating up
After pulling the dishwasher out from under the cabinet, I found it underneath near the back right side. I disconnected the old thermostat, unscrewed the clamp holding it into place, put the new thermostat in, screwed it back in and replaced the two plugs. Then I pushed the dishwasher back into place, and it initially didn't work until I found an online forum that was able to identify the reset command for my dishwasher (for the WDT710PAYM4, press any three buttons in a sequence of 1 2 3 1 2 3 1 2 3. After completing that all the lights lit up, and I shut the door leaving it for half an hour) Once the reset finished, the heated dry worked like it was suppose to.
first I removed lower basket. then removed lower sprayer attached to pump housing by unscrewing the cap by hand. the I removed the pump cover . there were six alan screw two of them were missing causing the failure of the seal spraying solution at the door. replaced the pumpseal working backwards until everthing was replaced.
The cap.nozzle is critical in transferring water to the upper wash tray in the "heavy wash" cycle only. If this part is defective, simply unscrew it by hand and install the new one by hand in seconds. This part is inactive in the "light wash" cycle.
Look for deteriation in the black rubber area of the cap. nozzle.
Ordering and tracking the shipment was a breeze, everything was very easy to do !!!!
actually my wife did the repair. she unsrewed the water sprayer and removed it, then unscrewd the star key screws and then replaced the seal. she put everything back the way it was and it is now ready to use and we no longer have the problem. just a suggestion...if you take some baking soda and some vinager you can clean the drain out. just simply poor in the soda and then the vinager.and it will fiz cleaning your drain.
Dishwasher made a crunching, grinding sound and then stopped working.
I followed the video available on partselect.com and was easily able to follow step by step the process of removing and reinstalling a new Drain and Wash Impeller and Check Ball.
Turned off electricity. Removed the interior door cover. Removed door switch. Replaced switches & reversed process. By the way - I am a woman & diagnosised, ordered part & fixed it myself - I have no experience in this field. THANKS for all your information on your site.
removed two hose clamps and old hose. slid new hose on existing fittings on dishwasher drain and disposal and tightened hose clamps. Turned it on for test run.
The upper spray arm was cracked where it mounted to the top rack.
Ordered a new upper spray arm from PartSelect. Shipping was fast and the correct part was recieved. Use a hair drier to warm the prongs that mount to the upper basket. The plastic is softer and will squeeze/fit in place without snapping off the "ears".
