66513742K601 Kenmore Dishwasher - Instructions

Many thanks for the repair instructions. My dishwasher has a black plastic cover over the control board but it was easily removed. I did take a photo of the board before I started to use as a reference in putting thing back correctly. Being 70 and never having done anything of this type I was nervous but the machine was broken anyway so what harm could I do. It WORKS...

My dish washer is a under the counter type.On mine there are two screws that screw into the bottom of the counter frame,these are located inside when you open up the door, they will be right on the inside and to the very front of the upper part of the door opening. Remove both screws. Now,be slow and start to pull the unit out from under the counter. Make sure you don't scrastch your floor,you may use a towel.If your dish washer's discharge hose is conected under the sink, go ahead and remove it. If your unit can be unpluged, unplug it. If not throw the breaker.Try to turn your unit on' if it does you still have power still on. Try again.With the unit pulled out so you can see the back, lay on your side and look for to long looking plastic nuts with a wire coming out of them. These nuts are holding your eleament in place.Unscrew both nuts and let them slide down the wires. Pull both of the wires off the eleament.now reach inside and remove the old eleament.Put new eleamen in place, reconect wires and tighten the nuts,caustion not to tighten nuts to tight.Ok hook the hose and eleectric back up,push the unit under the cabanet, and install the two screws.Really hopes this helps.

Read comments on-line here. Then removed both drawers, removed one screw from top filler tube. Gently pulled tube down just enough to remove small "button", after first putting a cloth over entire bottom of dishwasher to catch it if it, or screw, fell. Button goes in "pointy side" down. Squeezed new spinner onto button until it "popped" on. Replaced top screw, drawers and ran a load. Worked perfectly. Button was worn out. Would be nice if only button could be purchased.

Turn off power at breaker. Mine on same breaker as disposal. Removed the twelve torx head screws from inside of door (see the video on replacing the bi-metal fuse). Removed fuse from board, then removed spade connectors to test fuse with multimeter. Blown. Board is snapped in place. Remove the two plugs from the front side of board, the four plugs from the bottom and the ribbon cable. Used a screwdriver to gently bend clips holding board in place at the ribbon cable end of the board and lift out. Examination showed burned area around pin P4, the door neutral pin. Installed new board, re-connected all wires and ribbon cable. Installed new bi-metal fuse just like in video, reassembled door. Turned breaker on, ran normal cycle. Perfect. Wife thinks I'm a genius. Partselect saved me hundreds.

Repair was simple. Pulled out the old gasket and pushed in the new one.

Ordered Rinse Aid Cap and received the next day. Placed in the dishwasher Rinse Aid Cap position and locked in. A perfect fit.

Unhook electrical/water supply, removed dishwasher, flip upside down, Remove wire connector from motor, remove bolt from motor, turn motor and remove, install new motor in reverse process.

Pulled Dishwasher out, turned off power. Did not have to disconnect any hoses or electrical, because when I did the original installation, I left plenty of slack, so as to be able to pull it out. Next, tipped it on it's side, unplugged the harness, undid the bolt, turned motor 1/4 turn, pulled it out. To, re-install, just reversed the process. About 1 hour.Followed Excellent instructions on video. Was very impressed with delivery time. Only about 30 hours, from the time I ordered, to receiving part. Reg. ground.

pull and replace

Ordered the gasket on line. Received gasket in 3 days. Removed old gasket by pulling out in one piece. Pressed the new one in with my fingers and it fit perfectly and now have no leaks. Very easy fix.

Pulled out, put on it's side. Take pump off and put new one on and put all back together. Very easy. Video was helpful also.

The service video was great. This is a great product web site and service.... Thank you

just dropped in the new basket

Just had to take several screws out of old panel on dishwasher. Used the same screws to put on the new stainless panel. No wires to disturb. Was very easy. Works like a charm. Thank you Parts Select.

put new one in