Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
There was no problem
I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.
Actually, I found a video on Youtube with excellent instructions once you got past the really simple stuff like disconnecting power and water and drain. I would recommend just finding a fairly similar model on Youtube and follow their directions. It was really easy.
First I removed everything off of the bottom of the dishwasher. Then I removed the main center piece that everything mounts to. Then I reinstalled the new center piece with the help of some evoo cooking spray (extra virgin olive oil) I sprayed it on the rubber seal to aid in getting that center piece installed without a battle. Then I reinstalled everything else in the reverse order that I removed it. The evoo cooking spray works wonders for more than just cooking !!!
thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and install new switch and reconnect the wires.
I turned off the power to the dishwasher, removed the kick plate, raised the front levelers, disconnected the electric to the appliance, turned off the water supply to the appliance, disconnected the water supply, disconnected the drain system from the garbage disposal, unscrew the appliance from the countertop, then I remove the appliance from underneath the counter. I then tilted the appliance back and then in screwed the plastic retainers that held the heater element in place, removed the old one, replaced it with the new one in reversed the whole process
A plastic retainer pin for the bottom kick panel was missing.
simply line up the new pin with the rectangular slot in the kick panel and metal panel behind, slide the pin in and turn it with a flat blade screw driver. NOTE: the original pin was black. A black replacement part cost $29 plus shipping! A knock-off pin was only $6 plus shipping. I got the cheap one and colored it with a black Sharpee marker before installation.
Thanks to everyone for posting their experiences on changing the heater element. The most difficult part of the repair was getting the dishwasher out of the cabinet. I didn't know that I should disconnect the water line underneath the sink and this would make the removal easier. Also, because the copper water line going to the dishwasher was kinked, I ended up changing it with a flexible steel braided line.....much easier to install.
Once the dishwasher was out of the cabinet, I turned it over and easily removed the clips that held the heater element in.
I would definetly recommend people doing this repair themselves, it will save you a lot of money!!!!!
A wheel on the upper rack had fallen off. The wheel mount had worn.
Because the dishwasher is 15 years old I decided to replace all 4 wheel mounts. They were all worn and not clipping to the rack firmly. The repair is obvious. No tools required. Remove the stops on the end of the rack slides (manually squeeze the top of the stop and pull up, or you could use needle nose pliers) and slide the rack out. Just remove the old wheel mounts and clip the new ones in place. Slide the rack back in and snap in the stops.
clean light blinked 4 times and repeated this over and over
I took the valve off and actually hooked 110 volts to the vale and tried to blow through it and it would not let air pass through it. I replaced the the new valve in about 15 minutes and it works fine
A mouse was chewed through the hose and ate part of it. Di
Disconnected the damaged hose extension from the dishwasher outlet drain hose and the connection to the sink drain. Removed two clamps. One a spring clamp and the other a screw clamps. Connected the new extension hose with a spring clamp to the dishwasher outlet drain hose. Connected the other end to the sink drain with a screw clamp. Checked for leaks. Good to go!