Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replace lower dishwasher rack due to broken tines
Although the lower rack was a slightly different style than our original, it fit the dishwasher perfectly. We needed to transfer the silverware racks to the new rack and insert one set of removable tines. About 5 minutes and we are very happy with the repair.
Not enough water going into the dishwasher and screaming noise.
Other than the repair part being at the bottom of the dishwasher and you had to lie on your stomach to do the swap out, it was just one screw, move the part out a little closer to you then pull off one electrical wire, and pull off one small hose and using wrench unhook the other small hose.
Of course I had to take it apart a second time because of a leak, but using 3 or 4 circles of the white plumbers tape, it took care of the leak.
The repair was really easy. First disconnected electricity staring with fuses and removing wires from dishwasher, then disconnected drain hose and water hose. Pulled it out and removed pump turning clockwise no need for tools and same way installed new one. Very easy
I first turned the power off to the dishwasher. I then used the star bit to loosen the screws on the sides and top. Note that the 4 top screws are longer than the side screws. Once the screws were loose I used a clamp on each side to hold the door cover in place. Once the screws were removed, I released the clamps, raised the door then lifted the outer cover off. I then peeled the insulation back from the top to expose the dispenser. I used a small socket to remove the screws for the dispenser. I released the plug with a small slotted screw driver. I then exchanged the dispenser with the new unit being careful to correctly reinstall the black cover over the top. I reinstalled the door cover, being careful to tuck the insulation back in place. I then installed the screws using the clamps to hold the door in place during the reinstall.
You need to pull the unit out to get access to the spring connected to the rear leg frame. Use the everything in the kit. The rollers are upgraded and will guid the cable better.
i asked the vrtual repair stating the problem of my dishwasher machine ,he then give me two possible solution change the water presure switch which i did order the part and installed it and it works now..............thanks partselect.
Disconnected Power, Turned off water valve, disconnected drain return line, disconnected water line, removed two screws on inside-top that was mounted to counter, pulled out dishwasher while feeding power cord, drain line, water line. Turned Dishwasher on it's side and disconnected water line and water fill line from Fill valve Assembly. Disconnected power connector from Valve. Removed one screw from Fill valve assembly and removed Fill valve assembly. Installed Fill valve assembly and screwed screw back in. Installed Water line and water fill line from valve. Snapped power connector back in. Doubled checked Fill Valve connections to make sure they were tight. Slide Dishwasher back in while lines and power back through to under sink. Made sure Dishwasher was set in place and mounted two screws to counter. Connected water line to water valve and connected discharge line back to it's location. Turn water back on. Plug power back in. Turned unit on and checked for leaks at the fill Valve assembly, water line and discharge tube. Saved ~ $ 100.00. Easy job. I wished I didn't wait so long when it was making the noise for so long...Good luck..
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
I watched the video identifying the part and the procedure to make sure I could handle this. The phone attendant was also very helpful in making sure I ordered the correct part,which arrived in one day (amazingly). Everything was clearly described in the instructions and if you have done electrical work this would be relatively easy. You will need a specific screw driver bit to open the control panel but everything else is straightforward, just follow the instructions. Works perfectly now (I needed a new control panel about a year ago and Kenmore charged me $229 but it was just over a year since then....) PartSelect is a great service!
Stopped washing in cycle, LED code flashed 6 times
Since I had manual from initial installation I knew code meant heater was malfunctioning. Went to Sears, Lowes..no parts to repair. Instructed to go to appliance repair shop, closed of course...ordered online instead here and received in 2 days. Repair took 20 minutes. Super easy! Do not attempt to use adjustable wrench to tighten, use socket set as plastic electrode casings will be compromised. Takes some tork. Probably saved $100-$150 repair call. Wife was pleased. I was suprised how easy.
My dishwasher's heated dry cycle wasn't heating up
After pulling the dishwasher out from under the cabinet, I found it underneath near the back right side. I disconnected the old thermostat, unscrewed the clamp holding it into place, put the new thermostat in, screwed it back in and replaced the two plugs. Then I pushed the dishwasher back into place, and it initially didn't work until I found an online forum that was able to identify the reset command for my dishwasher (for the WDT710PAYM4, press any three buttons in a sequence of 1 2 3 1 2 3 1 2 3. After completing that all the lights lit up, and I shut the door leaving it for half an hour) Once the reset finished, the heated dry worked like it was suppose to.