Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
My dishwasher's heated dry cycle wasn't heating up
After pulling the dishwasher out from under the cabinet, I found it underneath near the back right side. I disconnected the old thermostat, unscrewed the clamp holding it into place, put the new thermostat in, screwed it back in and replaced the two plugs. Then I pushed the dishwasher back into place, and it initially didn't work until I found an online forum that was able to identify the reset command for my dishwasher (for the WDT710PAYM4, press any three buttons in a sequence of 1 2 3 1 2 3 1 2 3. After completing that all the lights lit up, and I shut the door leaving it for half an hour) Once the reset finished, the heated dry worked like it was suppose to.
Lost stop from one side of top rack. Rack could be pulled off track.
Looked at other side of top rack which still had the stop. Just had to orient the direction of the stop and push it firmly onto the rack arm. Took a couple tries, but it went in and locked. Works perfectly. Inexpensive and easy fix to to very annoying problem.
1.Check the lines for any obstruction. Gunk can easily build up. I have used the dishwasher for approx. 10 years. I do rinse/scrap dishes prior to loading. 2. Drain all remaining water. 3. Unplug the dishwasher. 4. Grab a towel and proper screw driver. Unscrew the bottom protective plate. Remove the insulation plate. 5. The drain pump is located to the bottom left. Have your towel under it. Unplug it gently. Turn counter clockwise to remove. 6. Install the new drain pump (reverse order) 7. Return the insulation plate. Screw back the bottom protective plate. 8. Plug in
Tried to clean old part and it did not work. Ordered the new part on Saturday and received it on Tuesday. Removed the old part and installed the new one. Ran the machine and it worked great. A big savings on not having to buy a new machine!!
Unplug dishwasher and slide it out from under cabinet. Remove old broken link (a heavy string between two plastic parts) and replace with new one. Slide dishwasher back and plug it in. Very easy and no tools required.
The old seal would often travel with the door when opened.
I removed the old seal and carefully cleaned the track into which the seal was fixed. No tools other than some ordinary cleaning liquid, cloth and small wooden piece to swab out the track. Easy and quick. As a note here, I first used the incorrect schematic for the unit and ordered the wrong seal. However after receiving the wrong part, I made the correction and reordered. I did this over the phone as I needed instructions to return the part. The person taking my order and answering my questions was very helpful and I want to take this opportunity to thank her.
I opened yutube and noted the tips on how to fix specific problems with my dishwasher. That "steve" guy was very helpful. I tested the old bi-metal fuse with no flow and ordered a new replacement through partselect. The part arrived in one day and was fitted quickly. I used the teat meter to confirm that the fuse was ok before I installed it. The only problem that I had was identifying the part and number from a diagram which I did not have.
Just removed the old seal and followed the instructions that came with the new one. Since the old one didn't have any adhesive on it ,I didn't use the adhesice on the new one. Problem solved!
Remove the mounting screws that hold the dishwasher under the counter top. Remove dust cover plates at the bottom of the machine. The machine will have to be pulled out, so turn off the water to the machine. Usually under the kitchen sink. Disconnect water supply and push it out of the way so the dishwasher can be pulled out. Pull machine out enough so you have access to the door cables and springs. The door will have to be in the closed(up) position to do the repair. Usually only one side is broken. Start with the broken side and copy the working side when installing new parts. Then repair the working side. To get the working side apart just pull on the spring and disconnect it from the cable. Do the reverse to reinstall.
Remove 2 screws on lower baseplate. Remove 2 screws that hold dishwasher inside cabinet( may be attached to counter top or side cabinets). Turn off water supply to dishwasher. Remove any connections such as water supply, electrical connection, or waste water line that prevent dishwasher from being pulled out about 3/4 of the way. With the dishwasher door closed, remove broken parts and replace with new parts. Pull on spring to make final connection of nylon cable. Reverse the above instructions for re-installing the machine.
the tines in the upper basket of the dishwasher were falling apart
Removed the old tines by pushing out the clips on the end and then installed the new tines and applied clips - took 10 minutes worked slick and the washer basket looks to be brand.