62945775 Kenmore Range - Instructions

Shut off 220 volt power to range. Removed two screws for cooktop element access. Used needle-nose pliers to remove power (2) and control (2) lugs and wires. Remove defective cooking element module, replaced. Reverse steps for new unit.

pull the stove out from wall unplug remove oven door take screw driver unscrew the two screws pull out old element install new element install the two screws plug in stove push back to wall done

I unplugged the stove and removed two screws on bottom of stove top (above oven door) one screw holding burner bracket in place. Took one wire off at a time and hooked to new burner, tightened all screws back down.

removed two screw and two wires from old element. Plugged in new element and mounted it back in less than 5 minutes time.

Replace the oven sensor per the excelent easy video you provided

The part was ordered the 26th of December in the AM and the part was delivered on the 27th. Installation was simple. The price was 35% cheaper than the big box store.

Watching the video of how to replace the sensor was great help and much appreciated, the only difference was that my wires were much shorter and I had to pull the oven out of the cabinet to get to the back of the oven to release the clip holding the wires together, unlike the video where the man jiggled the wires until the clip holding the wires together came through the little slot where the probe is attached, otherwise it was pretty simple, just a few extra steps to pull the oven forward to get to the rear to release the clip holding the wires together. Once I was able to release the clip I used one of the 2 adapters that was sent with the sensor probe and attached them after putting the wires through the hole where the probe was attached first then replaced the 2 screws that holds the sensor in place, slid the oven back in and turned the circuit breaker back on and it works perfectly. The video gave me the confidence to do this job though and I thank PartSelect very much for being a great company to help with videos and sending the parts so quickly.

We took the back off the stove and unscrewed the two screws from the inside holding the sensor on and pulled it through and plugged it in and then replaced the screws. Very easy. We are still having trouble as the display does not read the same as the tempature is in the oven.

This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.

first I checked continuity through the surface element (burner) switch (rheostat) which was fine. then found the screws holding the burner top on and removed, this made it possible to lift up the burner top and remove the burnt out surface element.which was easy to see. take down the number, buy a new one and re hook up the four wires to the new element. (always mark down where the wires went)

Unplugged the stove removed back cover plate unpluggeg two wires removed racks from oven removed two screws that hold bake element in place and reversed process

Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!

Read the ID number from label and ordered part on line. Part was delivered next day. Shut off power to stove and Pulled stove out from cabinet setting. Took out about 12 screws from back pannel and removed it. Pulled out wires (easily seen) from each side of heating unit at back of stove. Went inside oven and took out 1 screw (easily seen) on each side of heating element at back of oven. Heating elemnet came right out. Reversed procedure for installing. Only tool used is a small Phillips screw driver.

It was necessary to take the decorative glass and metal safety panel off using a screwdriver in order to get to the frame that holds the safety glass. It was hard to slide the new glass into the frame without help from a second person to hold the other pane in place.This was an easy repair to make I would just suggest having 2 people to hole things in place while replacing screws.

I did exactly what your instruction video showed. The most important thing to remember is to TURN THE POWER OFF FIRST.