62170419 General Electric Dryer - Instructions

There is a plastic female closure part in the dryer door that wouldn't close tightly around the metal male closure on the dryer. I popped out the plastic square with a screwdriver, popped the new plastic closure in with my thumb. Works great. I never even installed the new metal portion of the latch.

Watched the video on YouTube and everything went great!

I only ordered a lint filter with frame but wanted to let other's know that ordering from your site was extremely easy and the shipping was extremely fast!! I received my order with 2 days of placing my order. Thank you!!

the replacement part was easy to replace but remembering how the belt went back on took alittle more time..

The repair for the average untrained mechanicslly inclined " first off google directions/instruction picture step by step " we took off the wrong part which made this job difficult there is a part on the back that was removed prior to guided directions, called parts select they are awesome"our belt was delivered the next day on a 3 day weekend I was suprised second correct part sent anyone who took on this job , they will appreciatte all this . the belt was fairly easy to repair just do as directed follow guidelines. difficulty detaching a part that never should be"pain in the a" order your part from this company they rock" and picture guide and specific direction guideline @ this dryer has well outlived the money spent still kicking strong after several years of use hotpoint dryer

sort of followed instructions, would have beenhelpfull if they told me I HAD TO REACH INTO THE MOUTH OF A SABRE TOOTHED TIGER to install the new belt.

Had to tap three holes in the rear bearing to match the three attachment screws. Screw up with the part.

Based on the symptom (drum not turning), I figured that the belt was shot. I found a video on YouTube that described how to fix it. I also found directions here on this site on how to fix it! Here's what I did: step1: there were two screws holding the top on. took them off and the top swung up, exposing the drum and broken belt. step2: took off the two screws holding the front on. tipped the front forward so I could get the new belt around the drum. step 3: took the back plate off (10 screws). had to remove the exhaust tube first. cleaned out all the lint with the shop vac. there was plenty of lint everywhere. step 4: put the belt onto the motor pulley wrapping around the tension pulley. step5: put everything back together and plugged it in. everything worked fine. it took longer to vacuum all the lint out than it did for the actual repair.

take off door, take off front, mind the 2 wires for the door switch, take off top, take out enough screws on right side so it will lean out a bit for the drum to be removed. before removing drum you must remove the belt. pull the wheel to the right, minding the belt pattern for reassembly, its springy and will relieve tension. pull drum out. look to the left of the pulley and check to see any stray wire that may have pulled out while battling the belt. if you found a stray wire and it reaches the dryer motor find its home. on to the coils. I left assembly on dryer so I didn't have to figure out wire placement. the end connectors that the coils attach to are to be reused so don't get to mean with them. remove the end connectors minding how many wires it has and which of the 2 coils go to it. remove the old coils so as not to damage the very brittle ceramic insulators. on to the new, the instructions will tell you to stretch out the new coils to specified lengths. start with the shorter one first! just to see the stretchiness and how far is too far to stretch, if to long it will touch the heat shield and no good can come of that. after stretched out its time to string new coils in, carefully, so as not to stretch or collapse the coil. now hooking the end connectors to the ends of spring. I used 2 pliers to bend the tab a little bigger so it would cover the spring end. after springs are attached to ends and ends are in place, time to battle the drum and tensioner again, make sure plastic piece is on drum insert if equipped, put drum in place and bend tensioner down and install belt. put side screws on, then front and 2 wires , then top then door. plug in and start up. if unit doesn't start remember that stray wire going to the motor, you guessed it wire goes to the start switch. unplug and hook up the wire and it will work.

Ordered the recommended parts on-line and they showed up the next day. I followed the on-line repair video that described it all step-by-step.

The repair went very well, thanks to this site. Dixie

Unscrewed the top lid screws located in door opening.Removed lid.Unscrewed the front cover screws located at top corners of cover, underneath where the top lid was.Pulled out drum,removing belt at same time.Removed the rear bearing unit,installed new one.Really easy.Took front bearing off front cover,it just snaps on.Installed new bearing,with 4 new slides.Reassembled machine,replacing old belt at the same time.Done.It really is that easy.Spent more time cleaning lint out of dryer interior than actual mechanical work,I think.

Removed drum, replaced bearing. Installed new belt. Reinstalled drum. No problem

I watched video supplied from parts select, only took about 30 minutes, hardest part was putting belt back on, couldn't fit hands in easily, but once I did it, dryer is like new, can't hear a thing.

The ordering and receiving of the part were wonderfully easy, but the construction of the lint filter left a lot to be desired. Bits of wire extended past the edge of the frame and drew blood when held, so had to trim the wire screen that extended past the frame. Also, the wire screen was not attached continuously around the frame and had to be clamped and glued. I did appreciate that the filter fit my machine.