59673502200 Kenmore Refrigerator - Instructions

Was very easy after I found right tool to get out the screws. There were only 3 popped old one out and put new one in. I waited over a year thinking this was a difficult/expensive repair. So not true...22$ and 15 min. I will definitely recommend this store/site and maintain it for my future use.

Removed wiring from old ice maker and install on new. With 2 screws all ready in place hung ice maker on them. Attach wire connector into socket and install bottom screw to hold ice maker. Tighten top 2 screw and put wire guide in place. Drop wire guide down and ice started in 10 mins

Pretty easy repair, the hardest part was probably putting the back back on. Once the back was off it was a matter of unplugging the Relay Overload and Run capacitor from the compressor. Taking the new parts snapped them together plugged it back into the compressor and plugged it in. The fan came on the fridge started working and everything is working fine. Parts came in on time and will definitely order again from Part Select again when I need to.

had to replace side cap s because plastic pin sheared off

I first reviewed the video, paying attend to the order in which items were removed and put back in place. On the video, I noticed that the lid to the draw was put back into place before the draw. Following these instructions, the repair went extremely easy and fast. I would recommend reviewing the video first.

First of all, I do not consider myself very handy. Most of my simple home repair projects include at least 2 trips to the local hardware store and take twice as long as they probably should. So if I can do this anyone can. For once, rather than just blindly throw new parts at a problem I did check the water pressure to the icemaker first and then even tested the icemaker with a multi-tester to determine what was wrong. I had $5.00 mulit-tester in my workbench but had never actually used it before, so I found step by step instructions on another website on how to test the motor and it turned out that one of the circuits in the main motor was in fact bad. Since the motor was around $80.00 dollars and the Whole unit that's inside your freezer is about $120.00 I decided it was best to just go ahead and replace the entire unit rather than just the motor. From what I saw online normally replacing an Ice maker is fairly simple. Remove 3 screws swap the prewired plug along with the metal arm then just reinstall it. Somehow whenever I try a home repair it's never that simple. First of all, our freezer is on the bottom so removing the screws holding the ice maker meant that I had to climb over, around and under the freezer shelves in order to get to the ice maker itself. Also one of the screws is not visible from the front so I had to hold a mirror in one hand while I tried loosening the screw with the other. Since the metal arm that turns off the ice maker is not included in the replacement it had to be moved over. Of course it was stuck, so it did take a little time to get it loose because I was being careful not to bend it and have to order another one. Finally installing the new icemaker meant once again that i was climbing over under and around the basket in the bottom level freezer. There is probably an easy way to remove the entire drawer but I couldn't find the release tabs so when just pulling harder on the drawer didn't work, I thought it best to just work around it. Still all in all, not a difficult job, just a little time consuming. The guy in the video did the swap in about 6 minutes, it took me about 45.

Installation was really easy since the replacement part was identical to the OEM part. Removed the three mounting screws with a nut driver. This allows one to remove the icemaker from the wall and disconnect the wire harness plug from the icemaker. I never unplugged the harness from the rear wall of the refrigerator. Put the new icemaker in place, making sure to place the water fill tube in the proper hole. Plugged the wire harness into the new icemaker and tightened the three mounting screws. The icemaker worked perfectly from then on with clean ice cubes and no leaks.

Unplugged appliance. Using a small putty knife I moved the switch out far enough to grab it with pliers. Moved wiring to new switch and pushed into place after testing.

I took out the glass shelf that sits above the deli drawer. I removed the two veggie drawers. Unscrewed the two sides and pulled them out. The left side went right back in with the new part. The right side gave me concerns as it had the control slide. It came out easily. I had to R/R both roller slides with no problem. I took out the control slider parts and readily reinstalled them on the new piece. Reinstall of completed assembly went in without a hitch. It took very little time, I had the correct parts, screw holes were right on. Perfect fit, perfect part! It's as easy as that!!!

Took ice maker out all together we removed 4 to 5 screws had to remove axel to get the broken piece out and new one in my husband said it was easy in and out in about 15 minutes saved about 150. 00 Thanks partslect

Took off the only screw holding the drawers in place and removed old left and right end caps. Replaced with new parts and additional screws; then put on the cover so the drawer actually works again. Really easy job.

Replaced icemaker by using total kit. Watched youtube video put on by partselect folks. Very easy to follow.

I checked the part number and an exact replacement was ordered. The old unit was removed and what I failed to note was that the water supply hose for the new unit entered from the side. Further examination showed a small "break-out" piece at the rear of the unit. but I still had to do something about the hole in the side. I used a piece of metal tape to close off that hole, trimmed it to size, and installed the unit. It was really an easy install after I figured out what to do about the hole. Evidently, this unit is mounted on the side of the freezer compartment in some models. Reading the reports of others was a big help.

I put a stainless steel screw into the pantry end cap to hold the shelf trim in place so my pantry drawer would operate.

I followed the video and advice from the many others on this site and only have a few additional comments. First, the decorative cover on the front of the old unit is held on with two plastic teeth on the top and bottom of the cover. This was not at all apparent and it took me awhile to figure it out. I used a sharp knife to pry up the top edge until the teeth lost their grip on the metal notches in the old unit. Second, don't try to pull the cables out of the front of the old unit before removing that cover. It is held in with a plastic snap that must be depressed after the cover is removed. The video does a good job explaining how to remove the old metal arm and attach it to the new unit so that it will recognize the ice level in the bucket. Finally, don't bother looking around the web site for a button that enables you to add to these comments. You'll be contacted by email in a week or two for that.