Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replace the follow items Secondary Duel Water inlet valve Part no: WPW10341329 Control electric W10861900 Ice maker Fascia Heater Kit part PD00026897 W10619962 Ice Maker Assembly PS117392 replaced it two times And now icemaker is not ejected ice Roland Crenwelge 804-789-1795
Replace the follow items
Secondary Duel Water inlet valve Part no: WPW10341329 Control electric W10861900 Ice maker Fascia Heater Kit part PD00026897 W10619962 Ice Maker Assembly PS117392 replaced it two times And now icemaker is not ejected ice Roland Crenwelge 804-789-1795
Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.
I thought this was going to be much more difficult than it was. Take the bottom access door off (using a small socket - same size for all screws). Disconnect the plug to the motor. Unscrew the 4 screws holding the motor. Take the motor out. Unscrew the shaft screws on top (only 2) so you can manipulate it if need be up and down or spin it. Insert new motor and make sure shaft is seated correctly into the motor head. Screw motor back in. Screw shaft back in. Plug up motor. Screw bottom door back on. You are done. EASY!! Took me about 10-15 minutes to do. Much easier than most things.
We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing
bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!
Had to push the light switch to get lamp to light up. Removed power from refrig. and removed old light switch and replaced with the one I got from Partselect. Turned power back on and was done.
Repair was tremendously easy. All I did was remove old light switch by prying out with screw driver and plugging in the new light switch and pushing it into the hole. Simple! The instructions weren't needed, but they were very thorough.
The best part of the repair was how easy it was to find and order the part. Instead of searching the parts houses around town I just went to the PartSelect web site, quickly found and ordered the part in about five minutes, received the part the next day at my home and was ready to make the repair. Wow! What a pleasure for something to work the way it was meant to. Removed old switch located by prying out with sharp knife or screwdriver. Don't worry about breaking it or cracking plastic. Disconnect(unplug) wires from back of switch. Replace (plug-in) wires on back of new switch. Insert in location of old switch. Finisheed.
Light rocker switch broke and refrigerator light couldn't go on.
I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.
Internal light did not come on each time the door was opened.
After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.
I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.
Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.