Models > 59651673100 > Instructions

59651673100 Kenmore Refrigerator - Instructions

All installation instructions for 59651673100 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 59651673100
31-45 of 560
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

fridge side was not getting cold

  • Customer: neil from murfreesboro TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 11 of 15 people found this instruction helpful
first I removed the panels to see if the coils were getting frosty . Then I noticed that the fan was not spinning. I tested voltage to the fan and it was hot. I ordered the new fan put it in placve and, voila!.
Fixed my fride for under 50 bucks

Refrigerator wouldn't get cold enough.

  • Customer: Ty from Wentzville MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 10 of 13 people found this instruction helpful
Freezer would get cold at bottom and some of the refrigerator. Took of freezer back panel and located freezer fan. Took a meter and saw power was getting to it, but not working. Removed fan and replaced with new on, working like a charm. Cold air was not circulating enough throughout the unit because fan was not working. It was not the thermostat or adapter control.

Latch was broken on the filter cover and would not hold the filter in place.

  • Customer: Ken from St. Geogre Island FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 13 people found this instruction helpful
Ordered a new filter cover, received in 2 days and installed it in about 5 minutes. Worked perfectly.

Had to replace a hose connector at the base of my refrig/frreezer

  • Customer: Leo from Salem SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 16 of 32 people found this instruction helpful
Perhaps a helpful hint:

When aI received the hose adapter/connector, I inserted the 2 hose ends only to have water drip from the connection.
I used a utility knife to remove an inch from each side, then reinserted the hoses. That made the differnce. Dry as a bone.

LG

overload relay switch/bad compressor--buzzing sound, ends with click, retries

  • Customer: Nathan from Garland TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 9 of 11 people found this instruction helpful
Remove back cover. Disconnect power. Pull out overload switch off compressor. Remove capacitor. The overload switch i ordered came with instructions. What took the most time was figuring out if i dared installing it the way i thought best. The instructions, in my instance, were incorrect. My overload switch didn't have a terminal #1. Long story short, i looked at the circuit diagram it came with, and based on process of elimination based on terminal sizes, I put it together. But the instructions weren't accurate. All in all for the average DIY, not a bad repair at all. I am still afraid that my problem is the compressor, b/c even after the new part is installed it still occasionally tries starting but can't, and keeps retrying until it does. It is either a faulty relay switch or a faulty compressor. We'll see which one wins.

The crushed ice agitator kept slipping out of the bracket.

  • Customer: Charles from Plano TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 9 of 12 people found this instruction helpful
With the repair parts ordered and received from PartsSelect.com, I was able to install a new Ice Bucket and the crushed ice agitator assembly. This simple repair has the refrigerator dispencing ice like new.

Original parts had cracked due to cold weather

  • Customer: Brian from University City MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench set
  • 10 of 16 people found this instruction helpful
Original parts froze when the fridge was stored in the garage, so when we brought it in and hooked up the water supply we discovered the cracks.

I used a wrench to remove the back lower cover of the fridge. attached to that cover were both the parts I needed to replace. I removed one nut each per part so they were free of the back cover. Once free I unhooked the two electrical plugs per part and reattached the new part so as not to confuse the positions of the wiring. Then I did the same thing with the two hoses attached to each part, swapping old part for new. Once connected, I reattached the new parts to the back cover and replaced the back cover to the fridge. Connected the water line and tried the ice maker and water source on the door. I didn't realize it, but the filter, located in the refrigerator side of the unit had also frozen and cracked, so I had water now pouring from the fridge! Replaced that filter, cleaned up the water and everything is working great!

800 number customer service person Kim originally helped me locate the correct parts via schematic diagram, as no part numbers were visible on my broken parts. She was incredibly helpful and got the correct parts on her first guess ( she told me it was a guess but she was right on the money).

Crushed Ice Wheel began to fragment

  • Customer: Fred from Olathe KS
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 8 of 10 people found this instruction helpful
This is a side-by-side refrigerator. The crushed ice wheel is part of the icemaker bin auger, and it began to fragment, popping pieces of plastic into the ice dispenser and on into our drinks. The manuf. manual had nothing about parts in it, so GREAT thanks to Partselect for their website!!! Now, to dismantle the bin and auger is simple on this design: remove the bin from the freezer and allow it to defrost and dry; there are two small phillips-head screws on the front underside of the bin, holding the front panel in place - remove these screws and pop the front cover off; you'll then see two small phillips-head screws holding the auger-cap in place - remove these and pull the auger cap out, along with the auger; using a small pliers, remove the nut from the auger at the auger-cap, then slide the auger-cap off; at this point you just start removing washers, blades, etc, from the auger - MAKING SURE YOU KEEP THEM IN ORDER - until you reach the crushed ice wheel; separate the wheel from its metal brace, slide the wheel off and replace it; gradually replace all the other parts in order, cleaning them as you go, and simply put everything back together. It helps to keep the exploded parts diagram at hand - available on the Partselect website. It was a snap. The ordering process was simply and the part was delivered to my door on the second day after ordering.

Fridge side wasn't cooling and the Freezer was icing not letting air from the bottom going to the fridge side.

  • Customer: Sergio from Brookfield IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 7 of 8 people found this instruction helpful
First I unpluged, open the back right side, and I put a sponge to get the water that was melting from the unit, at front took the ice bucket off, pull the three shelvings and the lower drawer off too, unscrew three little nutscrews (1/4) from the middle and two from the bottom, pull the cover sideways and you can see the Thermostat on the left side top of the coils, just unplug one and cut the other, for the heater evaporator, there two clips holding it, pull the clips off and replace the unit, put everything back together and believe me will work, after two hours you can see the difference, I call many places for the repair i was gonna get charge $90.00 for the check, another $90.00 per hour plus parts, I just spend less than $70.00 Thank guys.

Fridge stopped working

  • Customer: Dan from Sumner WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 7 of 8 people found this instruction helpful
I called a repair man from a pretty large name to come out and take a look. He found out in about 10 minutes that it was a bad capacitor. The quote he gave me was $75 for the part and $175 labor. I tried my best not to laugh and tell him no thank you. He did have to charge me for him to show up, which was only $98.
So I used what he told(minus the "scrap it") and opened it back up. Although he had left wires everywhere and the broken pieces laying inside, I thought it was enough for me to order the part. PartSelect was very easy to navigate and ordering was a breeze. Took about 4 days to get the part and I ordered in the X-mas craze. Fixed it in about 15 minutes.

Refrigerator wouldn't cool

  • Customer: Fidel from Forest MS
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 8 of 11 people found this instruction helpful
First I removed the six screws from the cover. I then disconnected the two wires and pulled the small motor out with its base and removed two screws that hold it in place. I then changed the old one for the new one and set it back in its place. I then set the cover back and turned it on. I was happy again.

Ice stripper broken on ice maker

  • Customer: Kenneth from New Braunfels TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 12 people found this instruction helpful
I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!

ice bucket had a hole in it.

  • Customer: John C. from Erlanger KY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 6 of 6 people found this instruction helpful
removed old ice bucket by lifting up on the front and pulling straight out.Remove the front it just snaps into place.Remove the cutter comes out real easy.Put these parts on the new bucket.Slide the new bucket back in your done.

Water filter assy was broken and leaking

  • Customer: Brinda from Everett WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 21 people found this instruction helpful
The repair was fairly easy, just unscrewed the lower back panel and removed the ice maker hoses. the pulled the hoses out of the interior and replaced with new hoses. After running the water for a few moments, all is well and our family has ice and filtered water again. However, be careful when you are moving the fridge out of it's original space because the kitchen floor vinal ripped and now I have to replace the kitchen floor. What would have cost me about $40 to repair is now going to cost me much more.

No ice

  • Customer: Jon from Boise ID
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 8 of 12 people found this instruction helpful
1 screw remove assembly. Unplug cable harness and remove old cover and wire arm. Replace cover and wire arm and attach wire harness on assembly end. Re attach using screw removed in first step. Plug in wire harness. Making ice within 30 minutes.
All Instructions for the 59651673100
31-45 of 560