Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Small Constant Drip (Leak)
I pulled out the dishwasher removed the two heating element insulated wires and removed both threaded brass nuts and replaced them both. Problem solved. Luckily I have a local parts and repair store with a repairman that knows every part of every appliance ever made (no kidding, I have yet to stump him with a part or question). He did not have the parts, told me to go to partselect.com order two nuts, replace them both at the same time, and fix it myself because its an easy repair and not worth paying hundreds of dollars, if you can use a wrench. He was right, and partselect.com had the right parts, at the right price, easy to find and order, and I can impress the wife with my repair skills. Thanks again!
Door sagging when open & sever water leak from door.
The parts arrived 20 hours after ordering -great service & the parts were just like like the removed parts only new. The old door gasket was pulled from its groove & and the new gasket was installed witout using tools. No more leaking water.The door spring installation wesa bit more difficult. The front bottom was removed with a nut drive, the broken springs were fished out, new springs were pull onto the arms and the cover put back in place. Not a bad job for a crippled, one-eyed 82 year old man.
My Diswasher was leaking from around the door gasket.
I ordered a new door gasket and door spring. I unscrewed the two screws that hold the dishwasher in place and pulled it out. I pulled the old broken spring off with pliers and installed the new one ,,,very easy. I then took the new door gasket and soaked it in hot water in the sink for 15 min. That made it very soft and pliable to work with. I used pliers to pull the old gasket out then cleaned the area around the old gasket where crud had built up. I pushed in the new gasket working from top to bottom one side at a time. Turned it on an ran through a cycle and it works perfect now ,,,no leaks.
dishwasher was leaking at heating element connections
Both heating element brass nuts had a split in them. They had fallen off the heating element and were hanging on the electrical wires. I removed the wires from the heating element and removed the brass nuts from the wires. I then screwed the new nuts on the heating element and reattached the wires. problem solved. I want to thank you for having the parts I needed as Sears had discontinued them for this Kenmore appliance.
Removed lower panel; unmounted fill valve assembly. Installed two springs. Remounted fill valve assembly and reinstaslled the lower panel. Door must be in a near closed position to gain access to the door "L" spring brackets.
Removed old gasket and clean surfaces on tub and door before installing new gasket. New gasket has a small notch in the middle for top center. Install top then down sides for best results. Door gasket snaps into existing groove so no tools are required.
My dishwasher was leaking from and electrical connection at the heating element
There was an excellent "how to" video on the internet which also pointed me to the part I needed. I did not even remove the dishwasher as recommended. I removed the lower kick plate, removed the power connector at the leaking input, removed the bad nut and installed the new nut.
I removed the 2 screws that hold the dishwasher in place. Slide out the unit just far enough to access the brass nuts on the heating element. Pulled off the wire, and replaced the broken nut with the new nut. Replaced the wire, slide the unit back into place and reattached the 2 under counter screws. Done!!!
(leaking) heater element nuts cracked under dishwasher
power off, take off kickplate, unplug 2 wires and unscrew broken nuts, put new nuts on, plug wires back in,(run dishwasher one cycle to make sure no leaks) put kickplate back on, power on.
I only had one break, but bought both to replace. I don't agree with those that say you have to slide the dishwasher out to repair. I simply removed the lower kick plate, and replace the springs in no time. Very easy as was ordering the parts. I will return here for all my appliance parts in the future. Hope I don't actually need any.
Pulled the old gasket ou, cleaned the groove with a cloth. Then pushed the new one in, starting at the bottom. The curvatures are clearly marked, no guesswork.