Models
>
51270-W0
51270-W0 General Electric Washer - Overview
Sections of the 51270-W0
[Viewing 6 of 6]
Keep searches simple, eg. "belt" or "pump".
Door Strike
PartSelect #: PS455020
Manufacturer #: 5303207102
The door strike is attached to the door of your dryer and holds the door closed. If your dryer door is not closing, this might be due to the door strike needing to be replaced. This is a simple repair...
$16.13
In Stock
Timer Knob - Dryer
PartSelect #: PS755794
Manufacturer #: WE01X10160
Used with washer/dryer combo machines. This knob takes a D-shaped shaft.
$74.44
In Stock
Tension Idler Pulley
PartSelect #: PS418897
Manufacturer #: 131862900
The idler pulley on your washing machine allows the drive belt to operate smoothly. If your washer is not spinning or agitating, makes too much noise, or you notice a burning smell when it is operatin...
No Longer Available
Screw
PartSelect #: PS417463
Manufacturer #: 131302800
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$11.21
In Stock
Washer Lid Lock with External Safety Switch
PartSelect #: PS648775
Manufacturer #: 134101800
Mounting bracket on this part replaces old style ( You may need to drill off old bracket before mounting new lock).
No Longer Available
Direct Drive Pump
PartSelect #: PS417159
Manufacturer #: 131208500
This pump sucks the water out of your washers tub with one of its valves, and drains the water into a drain hose with the other valve.
No Longer Available
Water Inlet Hose Assembly
PartSelect #: PS1524416
Manufacturer #: 134211701
This water inlet hose is used in washers. The hose connects the washer water inlet valve to the water supply in your home. There are two solenoids on the valve, which are referred to as coils, and the...
No Longer Available
Clip
PartSelect #: PS428210
Manufacturer #: 218515401
This white clip is an inch long.
$14.81
In Stock
Questions And Answers for 51270-W0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 51270-W0
[Viewing 8 of 8]Door won’t close
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Lid Lock Assembly broke
The Lid Lock Assembly came super fast! The install would have been flawless, but the "pre-drilled" holes on the new Lid Lock Assembly were way to small. We found that out after we had reconnected the wires and gotten it into place. Aside from that small set back, the install went great! This repair is definitey not one that you would
... Read more
need to pay a repair person to do!
Read less
Parts Used:
-
Jenessa from Tacoma, WA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
74 of 92 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer leaking
removed front body panel (2 screws at bottom and pulled down panel), then used pliers to squeeze pinch clamps and pull back the two hoses off the pump. then removed the two pump clips that secure the pump in place and used screw driver to gently pry the old pump off the motor shaft, under that was the rubber pump slinger which was pulled
... Read more
off the motor shaft. The next step was to sand the rust off the motor shaft and apply some vasoline to lubricate the shaft and install the new pump slinger and pump on the motor shaft,put the pump clips back on and push the hoses on the new pump and slide the pinch clamps back into place, run test to check for leaks then re-install the front body panel.
Read less
Parts Used:
-
Michael from Woodridge, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
41 of 48 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washing machine will not drain or spin
removed upper cover, removed front cover, tested switch with digital VOM, removed and replaced!
2 screws, 4 wires! saved over $100 when compared to a bill from a repair service!
fast shipping too! will recommend others!
2 screws, 4 wires! saved over $100 when compared to a bill from a repair service!
fast shipping too! will recommend others!
Parts Used:
-
Heath Harris from Arnold, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
41 of 49 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!