Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Evaporator Fan Squeeking
Detected noise as coming from top freezer department, and tips and part diagram clearly pointed to evaporator fan. You go in through the freezer (you have to empty top half of freezer); removing the side rails holding the ice bin, and then the 4 outer screws (only 2 each side - not the middle ones) holding the 'auger' that turns the bin. From there it gets interesting in trying to disconnect the wires. You might consider taking some pictures of the connected wires - perhaps it doesn't matter, but several of them can be hooked up in reverse. After the ice marker is out, remove light and light cover, side rails/mounts that hold hold up ice maker. This leaves a large white cover that pops out (seam at bottom of it has two tabs that you can pop out) holding the fan; and then only a few more wires to disconnect to be able to get at the fan. Mine clearly had a wobble to it confirming the source of the squeak and need to replace. Install was just reverse -- a bit tricky to get some of the wires connected given the tight spaces. Overall, not difficult - but a lot of wires and screws to connect/disconnect. I didn't take any pictures as I disassembled, and found myself having to take some extra time to figure it out as I reassembled. In the end -- a silent and functioning refrigerator Good luck!
Removed ice dispenser and display with small screwdriver from front of the fridge. Pried out the whole piece slowly. This exposed the motor that activates the chute. Plugged in the new motor before any removal to verify the motor was the problem. When it worked, removed old and installed new. 3 screws. Piece of cake.
The replacement gasket does not have as strong a magnet as the original one. I removed the old one carefully so as not to cause more damage in case I have to put it back. Using Tongue suppressor I pushed new gasket into place and put a thin coating of protelem jelly on the gasket. I just have to make sure the door is closed each time to be sure of good seal.
This site was awesome! I was able to very quickly look up my refrigerator model, find the proper part number, and order the part. The only suggestion I would make is to update the cut sheet with a more clear version, it was a little difficult to make out the part number because the scan/drawing was fuzzy, but I was still able to make it out. Got the part in the mail very quickly and it was super easy to remove the old rail and install the new one. Take out the screws from the old one, remove the old rail, line up the holes, install the new one, and put back the screws. It's so nice to have a site like this to fine parts and order them! Too cool! Thank you so much!
Removed old rails and tapped new rails in place. The big problem was finding how to fix the drawer. After searching many online websites, It was my good fortune to find Partselect and a one of their service representatives who knew how to fix my drawer and they had the part.
Took off door per normal instructions. Removed the old stopper and hinge assembly (the hard rubbery parts had worn enough against each other to cause the annoying sound when opening and closing the door). Inserted the new stopper and hinge assembly. There was no locking nut on the newer part, so just had to level the fridge door without that part of the instructions (from normal LG instructions) Overall easy for a non-handy person and the annoying sound is gone. Wife is happier now.
whater valve whith a defected selenoid and water leaks.
First ,I unplug the refrigerator . 2nd i remove the back cover, clean the dust. 3th disconnect the water line, remove the all valve.. 4th unplug all the wires and code ea with a No,remove the water lines 5th replace the valve reconnect the wires and water lines.replace the back cover at last screw back the water line.check for water leaks . i found ease the valve replacement installation. .Thanks for the video.
unfortunately my fridge stopped working. I purchased another but wanted to try and repair the old one. when ew one arrived, the old one was supposed to be put in garage but instead was hauled away. Had delivery return next day but they had as already removed and lost the handle screw for the bottom freezer and the screw that holds handle in place. ordered the handle screw and picked up the nut. very simple to install the screw and put handle back on.
Uncoupled the old connector, replaced with new connector and attached supply line. Repair easy with right part, prior to ordering the right part I had tried a compression fitting and it still leaked. U-tube and others demonstrating repair assured me I was on the right path.
I screwed the old one out and replaced it with the new one. A no-brainer. The thing that was so amazing was that I ordered the filter on the intrnet and it arrived the very next day!!! I was very surprised and pleased with the very quick shipping!!!
Removed shelf that rails were mounted to. Used a std phillips screwdriver to loosen screws attaching the rails, three per side. Removed damaged rails, lined up new rails and tightened screws. Returned shelf to refrigerator and inserted tray on the new rails.