4RF302BXDW0 Whirlpool Range - Instructions

Simply had to turn off the power to the stove, unscrew the two screws holding the element in place, remove both wires from the contacts, attach the wires to the new element, screw the element back in place, and turn back on the power to the stove. Entire operation took less than 10 minutes!

I purchased a new infinite control switch 6". and replace the old one.

loosened the screw holding the block pulled it out toget to wire cut it about 4 inches long followed the inst.with block kit and it was a breeze. burner working fine now should have did it sooner.

I shut off the breaker checked for power then cut old plugs making sure to allow a little slack. Tightened down wire nuts put on a couple wraps of electrical tape and that was it. Burners work great now I would reccomend this product to anyone with a similar problem.

I determined the problem by swapping the 8 inch burner with a 6 inch burner. the 8 inch got hot when connected to the 6 inch wire harness. This told me that the 8 inch burner was good. The 6 inch failed to get hot so I determined the next logical thing was the power to the 8 inch burner. I used a multi meter to determine that power was getting into the control unit but no voltage was getting out. The controller was bad. I ordered a new controller and after unplugging the stove, replaced the controller in about 10 minutes. (Critical part of repair is to unplug unit from wall -220 volts!)

Very easily, took old one out, install new one, works perfectly. Directions were great, delivery service could not have been more efficient. Been baking ever since. thanks

First removed the oven door for easy access, removed two screws holding the element pulled old Element from back of oven to expose two connecting wires, disconnected wires and removed old Element. Connected wires to new Element pushed Element back into place and replaced two mounting screws put oven door back on, took about ten minutes. Very Easy!

Quick google time and problem was isolated to heating element and brought me here to partselect. It ship fast and oven was working again in no time. Super easy repair

The only problem we had was hanging on to the small screws that held the element up. No power screw drivers, so it took a little while to keep a hold of those screws. Considering we are 87 and 84 we feel great that we were able to replace both the bottom element and the broiler. I like the stove, and preferred not to shop for a new one. "Thanks for prompt great service and the video helped. Patty Montag

Just changed out the old and the new. That's all that was needed.

Cut the old wires off, removed the screw holding the clamp, installed the new parts. Problems I encountered were the wire nuts. They were too small for the wire gage of the replacement part and the original oven. I had larger wire nuts in my workshop. Also, why so many extra parts like the shrink wrap tubing, two metal clamps to hold the socket, etc.

First unplugged oven from wall. Removed two screws from back of oven above element. Pulled element out from oven back with wires attached. Gently detached clips from element. Replaced old element with new one and inserted wire clips onto end of element. Replaced element into back of oven and replaced screws. Yea, I did something!

I noticed that one of the burner blocks was completely burned and the others were corroded. I ordered blocks for all four burners. Installation was easy except for one block. The screw holding the bracket to the range top was completely corroded in place. I used a correct size easy-out, which is a left hand tap and drill, to remove the screw. That took about five minutes, including tracking the easy-out down in one of my many toolboxes. The entire replacement of four blocks took about one and a half hours. Stove top cooks like new on all burners! The part kit had all the right parts and they fit like a glove!

I had determined that the the burner itself was no longer capable of connecting because when I removed another burner and inserted it, it worked just fine. Also, the defective burner had not worked when inserted into another outlet. I was delighted to be able to purchase a replacement so quickly and easily on my own, without having to call a repair person or seek a retail outlet.

Unplugged the range, took the bad element out, and inserted the new one. Plugged the range back in. It worked fine....